Category: Support Antenna
Support Antenna
Showing 1–60 of 199 results
-
180 RPR / Upper section 1m (Towers) Televes
KSh50,458.00 -
180 series special ICT base RPR Televes
KSh13,870.00 -
Read moreAlcad AC-013 – Serie 998: 2mm cable clamps.
Material for the installation of guy wires in masts, telescopic masts or towers of great length.
Applications
The wire ropes are fixed to the mast by means of a ring clamp for masts up to ?40 mm or are fixed directly to the three tubes of the tower. Ring-headed expanding bolts are used to secure them to the floor or roof.
Characteristics
Steel wire ropes of ?3 mm. Wire rope grips for wire ropes of ?3 mm and ?6 mm and turnbuckles.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad AC-014 – Serie 998: 1/4” cable clamps.
Material for the installation of guy wires in masts, telescopic masts or towers of great length.
Applications
The wire ropes are fixed to the mast by means of a ring clamp for masts up to ?40 mm or are fixed directly to the three tubes of the tower. Ring-headed expanding bolts are used to secure them to the floor or roof.
Characteristics
Steel wire ropes of ?3 mm. Wire rope grips for wire ropes of ?3 mm and ?6 mm and turnbuckles.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad BB-001 – Serie 998: Bar clamp.
U-shaped clamp with one or three mast-fixing clamps.
Applications
Used to secure a mast to a railing or tube.
Characteristics
Made from M8 zinc-coated threaded rod with galvanised iron clamps for a ?60 mm mast.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad BB-002 – Serie 998: Double reinforced bar clamp.
U-shaped clamp with one or three mast-fixing clamps.
Applications
Used to secure a mast to a railing or tube.
Characteristics
Made from M8 zinc-coated threaded rod with galvanised iron clamps for a ?60 mm mast.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BE-001 Reinforced embedded base plate
KSh9,732.00Add to cartAlcad BE-001 – Serie 998: Reinforced embedded base plate.
Reinforced embedded base plate with soldered hooks, for TI-025, TS-015 and TS-025 towers.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BE-201 Embedded dish base (4x150mm)
KSh17,202.00Add to cartAlcad BE-201 – Serie 998: Embedded dish base (4x150mm).
Chimney clamp to fix the mast to a chimney which is held firmly in place by means of a wire rope which goes around the chimney and a system of turnbuckles.
Applications
Used as an alternative to wall brackets in installations which do not require very long masts. It allows antennas to be installed without having to carry out any work to the fa?ade of the building.
Characteristics
Made from round zinc-coated iron tube of ?30×1.5 mm and L-shaped profiles with a system of two long M8 turnbuckles. M8 clamps for ?50 mm masts.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BF-003 Fixed base
KSh8,342.00Add to cartAlcad BF-003 – Serie 998: Fixed base.
Bolting base plate, for TI-025, TS-015 and TS-025 towers.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BZ-400 Wall support for dish 85 cm
KSh7,530.00Add to cartAlcad BZ-400 – Serie 998: Wall support for dish 85 cm.
Chimney clamp to fix the mast to a chimney which is held firmly in place by means of a wire rope which goes around the chimney and a system of turnbuckles.
Applications
Used as an alternative to wall brackets in installations which do not require very long masts. It allows antennas to be installed without having to carry out any work to the fa?ade of the building.
Characteristics
Made from round zinc-coated iron tube of ?30×1.5 mm and L-shaped profiles with a system of two long M8 turnbuckles. M8 clamps for ?50 mm masts.
Downloads
Technical specification
Technical specification
Manuals
– pdf 17.23 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad BZ-401 – Serie 998: Wall support for dish 65 cm.
Dish support for the installation of dishes up to ?65 mm.
Applications
The support is used to install the dish on a wall, and is fixed by means of metals bolts.
Characteristics
The support is made from zinccoated iron. It has 4 fixing drills.
Downloads
Technical specification
Technical specification
Manuals
– pdf 17.48 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
-
Alcad CH-030 Chimney clamp 35 mm
KSh8,394.00Add to cartAlcad CH-030 – Serie 998: Chimney clamp 35 mm.
Chimney clamp to fix the mast to a chimney which is held firmly in place by means of a wire rope which goes around the chimney and a system of turnbuckles.
Applications
Used as an alternative to wall brackets in installations which do not require very long masts. It allows antennas to be installed without having to carry out any work to the facade of the building.
Characteristics
Made from roound zinc-coated iron tube of ?30×1.5 mm or ?35×1.5mm and L-shaped profiles with a system of two long M8 turnbuckles. M8 clamps for ?50 mm masts.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad CT-001 2mm steel cable. 100m
KSh8,470.00Add to cartAlcad CT-001 – Serie 998: 2mm steel cable.
Material for the installation of guy wires in masts, telescopic masts or towers of great length.
Applications
The wire ropes are fixed to the mast by means of a ring clamp for masts up to ?40 mm or are fixed directly to the three tubes of the tower. Ring-headed expanding bolts are used to secure them to the floor or roof.
Characteristics
Steel wire ropes of ?3 mm. Wire rope grips for wire ropes of ?3 mm and ?6 mm and turnbuckles.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad CT-003 3mm steel cable. 100m
KSh13,552.00Add to cartAlcad CT-003 – Serie 998: 3mm steel cable.
Material for the installation of guy wires in masts, telescopic masts or towers of great length.
Applications
The wire ropes are fixed to the mast by means of a ring clamp for masts up to ?40 mm or are fixed directly to the three tubes of the tower. Ring-headed expanding bolts are used to secure them to the floor or roof.
Characteristics
Steel wire ropes of ?3 mm. Wire rope grips for wire ropes of ?3 mm and ?6 mm and turnbuckles.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad GM-026 – Serie 998: Wall clamp 285 mm.
Brackets to secure the mast to a wall, to be fitted into the wall itself or to secure by means of metal bolts. Different strengths and lengths of brackets.
Applications
Two brackets are used to secure the mast to a wall.
Characteristics
Made from zinc-coated iron with an M8 clamp fixing system.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad GM-040 – Serie 998: Wall clamp 300 mm.
Brackets to secure the mast to a wall, to be fitted into the wall itself or to secure by means of metal bolts. Different strengths and lengths of brackets.
Applications
Two brackets are used to secure the mast to a wall.
Characteristics
Made from zinc-coated iron with an M8 clamp fixing system.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad GM-050 – Serie 998: Wall clamp 480 mm.
Brackets to secure the mast to a wall, to be fitted into the wall itself or to secure by means of metal bolts. Different strengths and lengths of brackets.
Applications
Two brackets are used to secure the mast to a wall.
Characteristics
Made from zinc-coated iron with an M8 clamp fixing system.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad GM-200 – Serie 998: Wall clamp for lag screws 200 mm.
Brackets to secure the mast to a wall, to be fitted into the wall itself or to secure by means of metal bolts. Different strengths and lengths of brackets.
Applications
Two brackets are used to secure the mast to a wall.
Characteristics
Made from zinc-coated iron with an M8 clamp fixing system.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad GM-350 – Serie 998: Wall clamp for lag screws 300 mm.
Brackets to secure the mast to a wall, to be fitted into the wall itself or to secure by means of metal bolts. Different strengths and lengths of brackets.
Applications
Two brackets are used to secure the mast to a wall.
Characteristics
Made from zinc-coated iron with an M8 clamp fixing system.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad GM-515 – Serie 998: Wall clamp for lag screws 500 mm.
Brackets to secure the mast to a wall, to be fitted into the wall itself or to secure by means of metal bolts. Different strengths and lengths of brackets.
Applications
Two brackets are used to secure the mast to a wall.
Characteristics
Made from zinc-coated iron with an M8 clamp fixing system.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad JV-335 – Serie 998: Ring and clamp.
Material for the installation of guy wires in masts, telescopic masts or towers of great length.
Applications
The wire ropes are fixed to the mast by means of a ring clamp for masts up to ?40 mm or are fixed directly to the three tubes of the tower. Ring-headed expanding bolts are used to secure them to the floor or roof.
Characteristics
Steel wire ropes of ?3 mm. Wire rope grips for wire ropes of ?3 mm and ?6 mm and turnbuckles.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad MT-210 – Serie 998: Mast 1500x35x1.5 mm galvanized.
Masts for antennas. Several sections of the mast can be added to extend its length. Secured to the roof by means of a special mast base for roof-tiles, to the wall by means of two brackets or to the chimney by means of a special clamp.
Applications
Used as a support for the installation of terrestrial TV and radio antennas.
Characteristics
Made from round galvanised iron tube. The different sections of the mast are assembled by inserting the upper part of the mast into the lower part of the other section, securing them with an M6 screw which passes through the tubes.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Add to cartAlcad MT-325 – Serie 998: Mast 3000x25x1.5mm for telescopic set.
Masts for antennas. Several sections can be assembled telescopically to make a longer mast. Secured to the roof by means of a mast base for roof-tiles, to the wall by means of two brackets or to the chimney by means of a special clamp.
Applications
Used as a support for installations of terrestrial TV or radio antennas. Installations where a high elevation for the antennas is required or where traditional antenna masts do not offer sufficient strength. The telescopic system allows the mast to be lowered without having to dismount the mast or release its guy wires.
Characteristics
Made from round, zinc-coated iron tube. The different sections of the mast are assembled by inserting the upper part of the mast into the lower part of the other section securing them with an M10 screw.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Add to cartAlcad MT-332 – Serie 998: Mast 3000x30x1.5 mm for telescopic set.
Masts for antennas. Several sections can be assembled telescopically to make a longer mast. Secured to the roof by means of a mast base for roof-tiles, to the wall by means of two brackets or to the chimney by means of a special clamp.
Applications
Used as a support for installations of terrestrial TV or radio antennas. Installations where a high elevation for the antennas is required or where traditional antenna masts do not offer sufficient strength. The telescopic system allows the mast to be lowered without having to dismount the mast or release its guy wires.
Characteristics
Made from round, zinc-coated iron tube. The different sections of the mast are assembled by inserting the upper part of the mast into the lower part of the other section securing them with an M10 screw.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Add to cartAlcad MT-338 – Serie 998: Mast 3000x35x1.5mm for telescopic set.
Masts for antennas. Several sections can be assembled telescopically to make a longer mast. Secured to the roof by means of a mast base for roof-tiles, to the wall by means of two brackets or to the chimney by means of a special clamp.
Applications
Used as a support for installations of terrestrial TV or radio antennas. Installations where a high elevation for the antennas is required or where traditional antenna masts do not offer sufficient strength. The telescopic system allows the mast to be lowered without having to dismount the mast or release its guy wires.
Characteristics
Made from round, zinc-coated iron tube. The different sections of the mast are assembled by inserting the upper part of the mast into the lower part of the other section securing them with an M10 screw.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad MT-345 Mast 3000x40x1.5mm for telescopic set
KSh11,104.00Add to cartAlcad MT-345 – Serie 998: Mast 3000x40x1.5mm for telescopic set.
Masts for antennas. Several sections can be assembled telescopically to make a longer mast. Secured to the roof by means of a mast base for roof-tiles, to the wall by means of two brackets or to the chimney by means of a special clamp.
Applications
Used as a support for installations of terrestrial TV or radio antennas. Installations where a high elevation for the antennas is required or where traditional antenna masts do not offer sufficient strength. The telescopic system allows the mast to be lowered without having to dismount the mast or release its guy wires.
Characteristics
Made from round, zinc-coated iron tube. The different sections of the mast are assembled by inserting the upper part of the mast into the lower part of the other section securing them with an M10 screw.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad MT-352 Mast 3000x45x1.5mm for telescopic set
KSh11,816.00Add to cartAlcad MT-352 – Serie 998: Mast 3000x45x1.5mm for telescopic set.
Masts for antennas. Several sections can be assembled telescopically to make a longer mast. Secured to the roof by means of a mast base for roof-tiles, to the wall by means of two brackets or to the chimney by means of a special clamp.
Applications
Used as a support for installations of terrestrial TV or radio antennas. Installations where a high elevation for the antennas is required or where traditional antenna masts do not offer sufficient strength. The telescopic system allows the mast to be lowered without having to dismount the mast or release its guy wires.
Characteristics
Made from round, zinc-coated iron tube. The different sections of the mast are assembled by inserting the upper part of the mast into the lower part of the other section securing them with an M10 screw.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad MT-410 Mast 2500x35x1.5 mm galvanized
KSh6,504.00Add to cartAlcad MT-410 – Serie 998: Mast 2500x35x1.5 mm galvanized.
Masts for antennas. Several sections of the mast can be added to extend its length. Secured to the roof by means of a special mast base for roof-tiles, to the wall by means of two brackets or to the chimney by means of a special clamp.
Applications
Used as a support for the installation of terrestrial TV and radio antennas.
Characteristics
Made from round galvanised iron tube. The different sections of the mast are assembled by inserting the upper part of the mast into the lower part of the other section, securing them with an M6 screw which passes through the tubes.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad MT-411 Mast 2500x40x2 mm galvanized
KSh9,164.00Add to cartAlcad MT-411 – Serie 998: Mast 2500x40x2 mm galvanized.
Masts for antennas. Several sections of the mast can be added to extend its length. Secured to the roof by means of a special mast base for roof-tiles, to the wall by means of two brackets or to the chimney by means of a special clamp.
Applications
Used as a support for the installation of terrestrial TV and radio antennas.
Characteristics
Made from round galvanised iron tube. The different sections of the mast are assembled by inserting the upper part of the mast into the lower part of the other section, securing them with an M6 screw which passes through the tubes.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad PI-101 Dish support (4x150mm)
KSh12,984.00Add to cartAlcad PI-101 – Serie 998: Dish support (4x150mm).
Chimney clamp to fix the mast to a chimney which is held firmly in place by means of a wire rope which goes around the chimney and a system of turnbuckles.
Applications
Used as an alternative to wall brackets in installations which do not require very long masts. It allows antennas to be installed without having to carry out any work to the fa?ade of the building.
Characteristics
Made from round zinc-coated iron tube of ?30×1.5 mm and L-shaped profiles with a system of two long M8 turnbuckles. M8 clamps for ?50 mm masts.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Add to cartAlcad RD-100 – Serie 998: Double horizontal reinforced support.
Arms for antenna masts, single or double, and another model to install antennas in vertical polarity.
Applications
Used as a support for several terrestrial TV and radio antennas with short masts. The use of arms reduces the necessary length of the mast and the flexor moment at its base.
Characteristics
Made from round zinc-coated iron tube ?30×1.5 mm with a securing system of two M8 fixing clamps.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Add to cartAlcad RS-500 – Serie 998: Horizontal reinforced aerial support.
Arms for antenna masts, single or double, and another model to install antennas in vertical polarity.
Applications
Used as a support for several terrestrial TV and radio antennas with short masts. The use of arms reduces the necessary length of the mast and the flexor moment at its base.
Characteristics
Made from round zinc-coated iron tube ?30×1.5 mm with a securing system of two M8 fixing clamps.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad SE-090 – Serie 998: Flange plate for lag screws.
Brackets to secure the mast to a wall, to be fitted into the wall itself or to secure by means of metal bolts. Different strengths and lengths of brackets.
Applications
Two brackets are used to secure the mast to a wall.
Characteristics
Made from zinc-coated iron with an M8 clamp fixing system.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad TA-001 Tiltable base for roof-top
KSh7,310.00Add to cartAlcad TA-001 – Serie 998: Tiltable base for roof-top.
Masts for antennas. Several sections of the mast can be added to extend its length. Secured to the roof by means of a special mast base for roof-tiles, to the wall by means of two brackets or to the chimney by means of a special clamp.
Applications
Used as a support for the installation of terrestrial TV and radio antennas.
Characteristics
Made from round galvanised iron tube. The different sections of the mast are assembled by inserting the upper part of the mast into the lower part of the other section, securing them with an M6 screw which passes through the tubes.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Read moreAlcad TE-014 – Serie 998: 1/4”tightener.
Material for the installation of guy wires in masts, telescopic masts or towers of great length.
Applications
The wire ropes are fixed to the mast by means of a ring clamp for masts up to ?40 mm or are fixed directly to the three tubes of the tower. Ring-headed expanding bolts are used to secure them to the floor or roof.
Characteristics
Steel wire ropes of ?3 mm. Wire rope grips for wire ropes of ?3 mm and ?6 mm and turnbuckles.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad TI-025 Tower lower section
KSh27,874.00Add to cartAlcad TI-025 – Serie 998: Tower lower section.
Triangular shaped tower (180x180x180 mm), formed by several intermediate sections and an upper section where the antenna mast is fixed. The tower is fixed to the roof or floor by means of a tower base which can be fitted into the roof or floor or secured by metal bolts. The tiltable base allows the tower to be lowered for maintenance work.
Applications
Installations where a high elevation for the antennas is required or where traditional antenna masts do not offer sufficient strength.
Characteristics
Made from zinc-coated iron, with round tubes of 20?x1.5 mm and M8 rod. The different sections and the base are assembled by means of three rods which fit inside the next round tube and are fixed by means of an M8 screw.
Downloads
Technical specification
Technical specification
Manuals
– pdf 20.74 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad TS-015 Tower-top section
KSh21,506.00Add to cartAlcad TS-015 – Serie 998: Tower-top section.
Triangular shaped tower (180x180x180 mm), formed by several intermediate sections and an upper section where the antenna mast is fixed. The tower is fixed to the roof or floor by means of a tower base which can be fitted into the roof or floor or secured by metal bolts. The tiltable base allows the tower to be lowered for maintenance work.
Applications
Installations where a high elevation for the antennas is required or where traditional antenna masts do not offer sufficient strength.
Characteristics
Made from zinc-coated iron, with round tubes of 20?x1.5 mm and M8 rod. The different sections and the base are assembled by means of three rods which fit inside the next round tube and are fixed by means of an M8 screw.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad TS-025 Tower-top section
KSh33,642.00Add to cartAlcad TS-025 – Serie 998: Tower-top section.
Triangular shaped tower (180x180x180 mm), formed by several intermediate sections and an upper section where the antenna mast is fixed. The tower is fixed to the roof or floor by means of a tower base which can be fitted into the roof or floor or secured by metal bolts. The tiltable base allows the tower to be lowered for maintenance work.
Applications
Installations where a high elevation for the antennas is required or where traditional antenna masts do not offer sufficient strength.
Characteristics
Made from zinc-coated iron, with round tubes of 20?x1.5 mm and M8 rod. The different sections and the base are assembled by means of three rods which fit inside the next round tube and are fixed by means of an M8 screw.
Downloads
Technical specification
Technical specification
Manuals
– pdf 20.74 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Anti-climb panels for 450XL towers 3 pcs Televes
KSh137,094.00Add to cartKit of 3 galvanized steel panels, for installation on each of the surfaces of a 450XL series tower. The panels are anchored with screws and improve the tower safety by preventing climbing and manipulation by unqualified personnel.
-
Add to cartPivoting embedded base with articulated anchoring system for a 450 XL – Reinforced range guy-wired braced tower. The base is painted red (RAL 3020). Televes 313412
-
Add to cart?Pivoting embedded base with articulated anchoring system for a 550 XL range guy-wired braced tower. Color Red (RAL 3020). Televes 314210
-
-
Add to cartFixed base for embedding galvanized in heats, for the anchoring of a tower of the 360 series. Anchoring system by means of fittings. Robotic welding. Maximum height of the Tower 360: 57m (according to calculation conditions). Fixed, no need for winds. Televes 308901
-
-
Base support T floor 750/200mm Televes
KSh12,614.00 -
Base Tilt Tower Series 360 Televes
KSh30,282.00 -
-
Add to cart3m lower section pivoting for the erection of a 550 XL-series tower. The section is painted red (RAL 3020).?Guy wires are required for pivoting sections. Televes 313911
-
Bottom section tilting Reinforced Tower 450 XL Hot…
KSh281,446.00Add to cart3m lower section pivoting for the erection of a 450 XL-series tower.?The section is painted red (RAL 3020).?Guy wires are required for pivoting sections.?Televes 313011
-
Add to cart3m lower section pivoting for the erection of a 550-series tower. The section is painted red (RAL 3020). Guy wires are required for pivoting sections. Televes 313901
-
Add to cart3m lower section pivoting for the erection of a 360 series tower.?Guy wires are required for pivoting sections.?Red color. Televes 308601
-
Bottom section tilting Zinc + Painting White 3m turret…
KSh163,824.00Add to cart3m lower section pivoting for the erection of a 360 series tower.?Guy wires are required for pivoting sections. White color. Televes 308602
-
Built-in tilting base G.C red turret series 550 Televes
KSh472,626.00Add to cartPivoting embedded base with an articulated anchoring system for the 550 range guy-wired braced tower. Concrete might not be necessary if bolted to a surface plate (ref. 312901). Hot-dip galvanized + painted red (RAL 3020). Televes 314201
-
Add to cartBurial plate, Hot-Dip Galvanizing 450 XL tower Underground mount plate using flat bars, no need for concrete. Used for embedding on it a pivoting base from 450 XL range (ref. 313412). Features The hot-dip galvanizing surface treatment provides enhanced durability in adverse corrosion conditions Grey finish 1.5×1.5m.
-
Add to cartBurial plate, Hot-Dip Galvanizing 450 XL tower Underground mount plate using flat bars, no need for concrete. Used for embedding on it a pivoting base from 450 XL range (ref. 313412). Features The hot-dip galvanizing surface treatment provides enhanced durability in adverse corrosion conditions Grey finish 1x1m.?
-
-
Embedded Pivoting base Zinc + RCP Tower 180 Televes
KSh12,484.00Add to cartEmbedded pivoting base for the anchoring of a 180 guy-wired braced tower.?Zinc + RCP. Televes 3048
-
Add to cartDomestic amplifier with 3 outputs (2+TV) to extend the terrestrial television domestic network.?The TV output provides a lower gain for direct connection to the television set (no outlet installation).?Equipped with LTE700/5G filtering. Televes 552220
-
-
Fixed base for screwing/embedding series 180 Televes
KSh28,300.00Add to cartFixed base of hot galvanized screw, for the anchoring of a freestanding tower of the series 180. It is possible to convert it into a recessed one by using its televes-3029 hardware. Televes 303801
Popular Products
-
Starlink Mini Dual USB Car Charger with
DC Cable & Voltmeter - 9.84FT/3M
-
Starlink Mini Versatile 3-in-1 DC Power
Cable Replacement - 9.8FT/16.4FT/32.8FT
-
Starlink Gen2 Rectangular Satellite V2
Replacement Extension Cable - 32.8FT/75FT/150FT/300FT
-
Starlink Flat High Performance Ethernet
Adapter - SPX Plug to RJ45 Cable Extension
-
DC 9V to 28V Boost Converter with DC
Power Cable for Starlink Mini
Products
-
Starlink Mini Dual USB Car Charger with
DC Cable & Voltmeter - 9.84FT/3M
-
Starlink Mini Versatile 3-in-1 DC Power
Cable Replacement - 9.8FT/16.4FT/32.8FT
-
Starlink Gen2 Rectangular Satellite V2
Replacement Extension Cable - 32.8FT/75FT/150FT/300FT
-
Starlink Flat High Performance Ethernet
Adapter - SPX Plug to RJ45 Cable Extension
-
DC 9V to 28V Boost Converter with DC
Power Cable for Starlink Mini