Category: Mast
Mast
Showing all 37 results
-
Alcad AM-160 Amplifier UHF 20 dB LTE mast 24 vdc
KSh5,370.00Add to cartAlcad AM-160 – Serie 903: Amp uhf 20 db lte mast 24 vdc.
Broadband amplifiers for masts, compatible with LTE mobile telephone signals with amplification band in UHF 470-790 MHz. They have one or two inputs to amplify and combine the signals from the antennas. They are fed through the coaxial cable from a power supply unit installed inside the building. They incorporate a switchable DC path, allowing power to be supplied to a preamplifier.
Applications
Individual digital and analogue terrestrial TV installations which are affected by the transmission of LTE mobile phone signals and which require low gain.
They amplify and mix the signals from several antennas.
The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, covered by a weather-resistant plastic casing.
Easy to open and close, the chassis can be tilted to facilitate manipulation.
It can be installed either on a mast, by means of a polyamide clamp, or on a wall.
Resistant to sun and water (IP53).
Greater insulation between inputs and outputs.
F-type connectors for screwing or crimping.
Accessories
9030086 AL-100 24 power supply unit.
9120039 CM-004 Male F connector for ?6.6 mm coaxial.
9080023 MC-302 Male F connector for RG-6 coaxial, ?7.0 mm.
9080030 MC-304 Male compression F connector for RG-6 coaxial, ?7.0 mm
DownloadsTechnical specification
TECHNICAL SPECIFICATION
Manuals
MANUAL AM-160 PDF 142.09 KB?
Certificates
CE_DECLARATION-TV_SYSTEMS PDF 65.95 KB
Technical specifications
-
Add to cartThe Televes 5354 mast amplifier has 2 inputs and 4 outputs that also allow the passage of the signal of a parabolic antenna, with an amplification power of 21db.
-
![Amplifier Mast NanoKom 3e/1s EasyF BIII/UHF[dc]/FMmix...](https://adishnetservices.com/wp-content/uploads/2025/04/amplifier-mast-nanokom-3e1s-easyf-biiiuhf-dc-fmmix-1224v-lte700-televes-320x320.jpg)
Add to cartMasthead amplifier for the amplification and combination of terrestrial television signals coming from several antennas. LTE700.?Equipped with 3 inputs: the signals on the BIII and UHF inputs are amplified, whereas the FM signal is only combined.?Televes 561821
-
![Amplifier Mast NanoKom 3e/1s EasyF UHF[dc]/UHF/VHFmix...](https://adishnetservices.com/wp-content/uploads/2025/04/amplifier-mast-nanokom-3e1s-easyf-uhf-dc-uhfvhfmix-1224v-lte700-televes-320x320.jpg)
Add to cartMasthead amplifier for the amplification and combination of terrestrial television signals coming from several antennas. LTE700.?Equipped with 3 inputs: the signals on both UHF inputs are amplified, whereas the VHF signal is only combined. The amplifier is powered through the output coaxial cable. Televes 561721
-
![Amplifier Mast NanoKom 3e/1s EasyF UHF/UHF[dc]/FImix[dc]...](https://adishnetservices.com/wp-content/uploads/2025/04/amplifier-mast-nanokom-3e1s-easyf-uhfuhf-dc-fimix-dc-1224v-lte700-televes-320x320.jpg)
Add to cartMasthead amplifier for the amplification and combination of terrestrial and satellite television signals coming from several antennas. LTE700. Equipped with 3 inputs: the signals on both UHF inputs are amplified, whereas the SAT signal is only combined.
Allows DC pass towards the satellite input to power the LNB.?Televes 561421 -
Amplifier Mast NanoKom 3e/1s EasyF…
KSh11,174.00Add to cartMasthead amplifier for the amplification and combination of terrestrial television and satellite signals coming from several antennas. LTE700.?Equipped with 3 inputs: the BIII/UHF input signal is amplified, whereas the FM and SAT signals are only combined.?Allows DC pass towards the satellite input to power the LNB. Televes?561521
-
![Amplifier Mast NanoKom 3e/1s EasyFUHF[dc]-VHFmix-FImix[dc]...](https://adishnetservices.com/wp-content/uploads/2025/04/amplifier-mast-nanokom-3e1s-easyfuhf-dc-vhfmix-fimix-dc-12-24v-lte700-televes-320x320.jpg)
Add to cartMasthead amplifier for the amplification and combination of terrestrial and satellite television signals coming from several antennas. Equipped with 3 inputs: the UHF input signal is amplified, whereas the VHF and SAT signals are only combined.?Allows DC pass towards the satellite input to power the LNB. Televes?561621
-
Add to cartKit shielded mast Amplifier SBA-103-C60 + Power supply APB-224-M
Features
DC bypass for active antennas
Increased output power 113 dB?V (DIN 45004B IMD-60dB)
Supply voltage +12 VDC and +24 VDC
High output level
Optimum design for very low noise figure
Power supply: The smallest and optimum power consumption
Specifications
MODEL SBA-103-C48
REF. 1304
Frequency band MHz 470 – 694
Tickets 1 UHF
Nominal gain dB> 34
Gain regulation dB
0 – 15
Noise figure (typ.) dB ? 3
Output level (DIN-B, -60dB) dB?V 113
Supply voltageVDC
mA
+12 / +24
60/70
Current pass Yes
Operating temperature ? C -10 … +60
Protection index IP IP54
Dimensions mm 96 x 125 x 46
Weight kg 0.370MODEL APB-224-M
REF. 3437
Regulation type switched
Departure 2
Mains voltage (50 Hz) VAC 100 – 240
Output voltage VDC +24 (? 5%)
Current max. exit mA 100
Frequency band MHz 47 – 862
Insertion attenuation dB ? 4
Current pass mA 300
performance % > 70
Dimensions mm 50 x 50 x 25DATASHEET
-
Add to cartIKUSI SBA-101-C48. Multiband mast amplifiers Adapted to the first and second digital dividend.
Features
Adapted to the first and second digital dividend
Very high UHF gain.
Interstage variable attenuators.
Optimum design for very low operative noise figure.
Internal injection-moulded zinc alloy housing with F type ports.
Technical specifications
MODEL
SBA101-C60 SBA101-C48 REF. SBA101 Series
1295 Frequency range MHz 470 – 790 (1st dividend)
1296 470 – 694 (2nd dividend)
RF inputs 2
UHF UHF
Nominal gain dB >36
Gain adjustment dB 0 – 15
Noise figure dB < 5 Output level (DIN-B, -60dB) dB?V 105 Input isolation dB ?26 Operation voltage VDC +24 Consumption mA 55 Dimensions mm 96 x 125 x 46 ? MANUAL/DATASHEET -
Add to cartIKUSI SBA-102-C48. Multiband mast amplifiers Adapted to the first and second digital dividend.
Features?
Adapted to the first and second digital dividend
Very high UHF gain.
Interstage variable attenuators.
Optimum design for very low operative noise figure.
Internal injection-moulded zinc alloy housing with F type ports.
Technical specifications
MODEL
SBA102-C60 SBA102-C48 REF. SBA102 Series
1301 Frequency range MHz 470 – 790 (1st dividend) 47 – 240
1302 470 – 694 (2nd dividend)
RF inputs 2
UHF BI/FM/DAB/BIII
Nominal gain dB 25 -1
Gain adjustment dB 0 – 15 –
Noise figure dB ? 2 1
Output level (DIN-B, -60dB) dB?V 106
Input isolation dB ?26
Operation voltage VDC +24
Consumption mA 45
Dimensions mm 96 x 125 x 46?
MANUAL/DATASHEET
-
Add to cartShielded mast amplifier. Frequency range 470-790 MHz
Features
DC bypass for active antennas
Increased output power 113 dB?V (DIN 45004B IMD-60dB)
Supply voltage +12 VDC and +24 VDC
High output level
Optimum design for very low noise figure
Specifications
MODEL SBA-103-C48
REF. 1304
Frequency band MHz 470 – 694
Tickets 1 UHF
Nominal gain dB> 34
Gain regulation dB
0 – 15
Noise figure (typ.) dB ? 3
Output level (DIN-B, -60dB) dB?V 113
Supply voltageVDC
mA
+12 / +24
60/70
Current pass Yes
Operating temperature ? C -10 … +60
Protection index IP IP54
Dimensions mm 96 x 125 x 46
Weight kg 0.370DATASHEET
-
Add to cartIKUSI SBA-190-C48. Multiband mast amplifiers Adapted to the first and second digital dividend.
Features?
Adapted to the first and second digital dividend
Very high UHF gain.
Interstage variable attenuators.
Optimum design for very low operative noise figure.
Internal injection-moulded zinc alloy housing with F type ports.
Technical specifications
MODEL
SBA190-C60 SBA190-C48 REF. SBA190 Series
1307 Frequency range MHz 470 – 790 (1st dividend) 950 – 2400
1308 470 – 694 (2nd dividend)
RF inputs 2
UHF SAT
Nominal gain dB 35 -2
Gain adjustment dB 0 – 15 –
Noise figure dB ? 2
Output level (DIN-B, -60dB) dB?V 105 –
Input isolation ? ?26
Operation voltage VDC +12 / +24
In the case of not using the SAT input, it can be supplied with +24 VDC
Consumption mA 40
Dimensions mm 96 x 125 x 46?
MANUAL/DATASHEET
-
Add to cartFrequency range: UHF C21-69 (470-862MHz)
Gain: 25-35dB
Noise Factor: 2.0dB
Maximum input level: 80 dBuV
Maximum output level 35 dB/M3: 105 dBuV
Power: 24 Volts
Consumption: 35mA
Dimensions: 112x98x56mm
Mounting: Pole or wall -
Add to cartLTE2 Mast Amplifier Kit
Characteristics
UHF 25dB LTE2 mast amplifier (Ref. 7322-L2)
1 input / 1 output
Frequency range: 470 ..694MHz (C21 ..C48)
LTE rejection (5G)
Ultra low noise
Gain: 10-25 dB (adjustable)
High selectivity
Built-in GSM trap
Power indicator LED
Pole or wall mount
Power supply (Ref. 2436)
High efficiency power supply
24Vdc stabilized
Short circuit protection
LED power indicator
Wall or DIN rail mounting
Specifications
7322 preamplifier
7322
Frequency range MHz 470 – 790 (ch. 21-60)
Gain dB 10-25 adj
Noise figure dB 2.0
Max. mild input dB?V fifty
Max. output level dB?V 100
Power supply VDC 24
Consumption mA 35
Dimensions mm 120 x 115 x 50
2434 power supply
2434
Outputs – two
Insertion loss dB 4
Isolation between outputs dB 10
AC input voltage / Frequency / Power – 230 V ~ / 50 Hz / 4.8 W
DC output voltage VDC 24
Output current mA 150
Dimensions mm 110 x 94 x 41 -
Johansson 7332DC 5G RED Preamplifier 10-34 dB
KSh4,114.00Add to cartUHF preamplifier
7332DC
Features
1 UHF input/1 output
Selectable DC current step
Output level up to 108 dB?V
LTE (5G) rejection
low noise figure
Adjustable gain 10-34 dB
Power LEDs
Operating voltage 12-24 VDC
Wall or mast mount
Specifications
Frequency range: 470-694 MHz (Channels 21-48)
Gain: 10-34dB
Noise figure: 2.0 dB
max level input: 78 dB?V
max level output (IM3: 2c/-60dB): 108 dB?V
Power supply: 12-24 VDC
Consumption: 115 mA (12V) / 65 mA (24V)
Connectors: F
Mounting: Mast or wall
Dimensions: 122 x 98 x 56mm -
Add to cartJOHANSSON 7332DC AMPLIFIER KIT AND 2436 POWER SUPPLY
7332DC UHF Preamplifier
1 UHF input/1 output
Selectable DC current step
Output level up to 108 dB?V
LTE (5G) rejection
Low noise figure
Adjustable gain 10-34 dB
Power LED
Operating voltage 12-24 VDC
Wall or mast mounting
Source 2436
Departures – 2
Insertion loss dB 4-5
Isolation between outputs dB 10
Input voltage/Frequency/Consumption – 100-230 V~ / 50 Hz / 4.6 W
Efficiency level – VI
Output voltage VDC 24
Output current mA 150
Dimensions mm 95 x 76 x 35
24V power supply 150mA 2 outputs
High-efficiency
24V stabilized
Short-circuit protection
Power LED indicator
Wall or DIN-rail mountable with clips (included) -
Add to cartVHF: 5-23dB / 2xUHF Ch21-48 LTE(5G): 12-32dB 12-24V
7412 Preamplifier:
1 x VHF input / 2 x UHF input
1 wideband output
Up to 111dB?V output power
5-23dB adjustable gain on VHF
12-32dB adjustable gain on UHF
LTE (5G)
Low-noise
Power indication LED
12-24 VDC operating voltage
Specifications
Input? -? VHF (BIII/DAB)?? UHF (Ch. 21- 48)??
Frequency range? MHz 170-240? 470-694?
Gain dB 5 – 23? 12 – 32?
Noise Figure? dB 2.5 1.5
Max. input level? dB?V 95 78
Max.output level?
(IM3: 2c/-60dB) dB?V 111 108
Consumption? – 1,7 W / 120 mA (12V) – 70 mA (24V)?
Connectors – F
Mounting – Mast or wall?
Dimensions mm 122 x 98 x 56? -
Add to cartUHF preamplifier
7412DC
Features
1 x VHF input (BIII/DAB) / 2 UHF inputs
broadband output
Selectable DC current step
Output level up to 112 dB?V
Adjustable gain on VHF 5-23 dB
Adjustable gain on UHF 10-32 dB
LTE (5G) rejection
Very low noise figure
Power LEDs
Operating voltage 12-24 VDC
Wall or mast mount
Specifications -
Add to cartVHF/2UHF Preamplifier / 2 Outputs
7413DC
Features
1 x VHF input (BIII/DAB) / 2 UHF inputs
2 broadband outputs
Selectable DC current step
Output level up to 109 dB?V
Adjustable gain on VHF 0-20 dB
Adjustable gain on UHF 8-28 dB
LTE (5G) rejection
Very low noise figure
Power LEDs
Operating voltage 12-24 VDC
Wall or mast mount
Specifications -
Johansson 7463 LTE amplifier 2 inputs 2 outputs
KSh2,360.00Add to cartFrequency range 174-240 / 470-790 / 174-240 + 470-790 MHz
Gain VHF: 7-22 UHF: 7-22dB
Noise figure 3.5 dB
max. input level 80 dB?V
max. output level 105 dB?V
Power supply 5-24 VDC
Consumption 35mA @ 24VDC / 90mA @ 5VDC
Dimensions 112 x 98 x 56 mm2 universal input: VHF only / UHF only or VHF+UHF (switchable with jumpers)
2 broadband outlets
output up to 105dB?V
adjustable gain 7-22dB on VHF
adjustable gain 7-22dB on UHF
LTE (4G) + GSM rejection
low noise
LED power indicator
DC current pass (with jumper)
power supply 5-24 VDC -
Add to cartAmplifier kit SMART 3 inputs + FA LTE2 (5G) Johansson
It has never been easier to combine 2, 3 or 4 antennas for the reception of full HDTV signals. The combination of several terrestrial antennas to receive full HDTV signals in single family homes (SFU) is often a problem. Most of the time, the signal from several antennas is combined using a simple distributor, but this solution does not work.
4 dB (minimum) losses = we only have half the signal when 2 antennas are combined
Channels on the same frequency are lost
Low isolation between adjacent channels
Many interruptions due to poor signal qualityViewers tend more and more towards terrestrial TV reception. But the current situation is not at all optimal … Therefore, the market needs a solution that offers:
Better signal quality
More channels
Plug & Play installation (no configuration required)
Mast amplifier SMART AMP 3 inputs LTE2 (7473L2)
The Smart Amp performs an automatic search of all channels, amplifies weak signals while keeping channels strong
All output channels have uniform and stable power
Handles even the most difficult situations with adjacent channels
Fully automatic channel scan and processing function at startup and after double reboot
Automatic recognition of the country’s channel plan
SAW filters for LTE-5G protection on all inputs
Weather-resistant outer shell for pole mounting
DC power via coaxial cable
All ports protected against electrostatic discharge
Meets RED CE standard
Output level: 85dB
2-outlet power supply (2437)
High efficiency power supply
Stabilized 12Vdc / 400mA
Short circuit protection
Power LED indicator
Wall or DIN rail mounting
specs
Parameter Unit KIT7472L2
Tickets – 3
LTE rejection – 5G (CH48) (> 694MHz)
Channel plan –VHF BIII + UHF
Different channel plans available
LTE band rejection dB > 40
Departure – 1
Output power dB?V 85
Frequency range MHz 174 – 862
LTE band reuse –L2 = CH49-69 (694MHz-862MHz)
ON-OFF switch
Adjacent channel isolation dB > 35
Input sensitivity dB?V minimum 40
Feeding – 12V / 300 mA (DC through coax) (350mA – 4 inputs)
Power supply – External power supply (ref. 2437 – 2 outputs)
Dimensions mm 120 x 115 x 50
Operating temperature ?C -20 to +50 -
-
Add to cartBand: BI / III-DAB / FM / UHF1 / UHF2. Frequency range (MHz): 47-68 / 175-254 / 88-108 / 470-862. Gain: 25 – 38. Regulation (dB): 15/20/15 / 15. Noise figure (dB): 4/4 / 7.5 / 7.5.
-
Mast G.C 3m ? 45mm thickness 2mm Televes
KSh15,982.00Add to cartHot galvanized steel mast, with excellent resistance to corrosion that guarantees the longest weathering. Televes 301002
-
![Mast mixer 3e/1s EasyF BI/FM-BIII/DAB-UHF[dc] Televes](https://adishnetservices.com/wp-content/uploads/2025/04/mast-mixer-3e1s-easyf-bifm-biiidab-uhf-dc-televes-320x320.jpg)
Add to cart3-input combiner for several terrestrial bands. Includes mast-mount case for outdoor installation.?Allows current pass from output to UHF input to power a mast amplifier or a BOSS system.?Orange colour. Televes 404010
-
![Mast mixer 3e/1s EasyF VHF-UHF[dc]-UHF Televes](https://adishnetservices.com/wp-content/uploads/2025/04/mast-mixer-3e1s-easyf-vhf-uhf-dc-uhf-televes.jpg)
Mast mixer 3e/1s EasyF VHF-UHF[dc]-UHF Televes
KSh4,310.00Add to cart3-input combiner for several terrestrial bands. Includes mast-mount case for outdoor installation.?Allows current pass from output to UHF input to power a mast amplifier or a BOSS system.?Orange colour. Televes 404110
-
Add to cartMFA 617- mast amplifier
Features
24 VDC supply
1 input mast amplifier
LTE protection LTE 700
Gain: 10 – 25/15 – 30 dB
Output level: 104 dB?V.
High resistance to external disturbances
High resistance to the corrosion
Optimized mechanism for easy installation
Optimized mechanism for easy installation
Neoprene clip for cable fastening
F female connectors.
Waterproof case.
RF shielded and CE approved (EN 50083).
Specifications
ORDER INFORMATION
EAN Number 5702663405172
CHARACTERISTICS
Type Amplifier – mast
Max. Output level (@ -60dB IMD) 104 dB?V
FREQUENCY
Input 1 – frequency 174…230 / 470…694 MHz
Input 1 – band BIII(DAB) + UHF
Input 1 – channels 5…12 / 21…48
LTE protection @ 700Mhz
GAIN
Input 1 – gain 10…25 / 15…30 dB
Input 1 – noise figure <4.0 dB LOSS Rejection @ 714 MHz (Ch. 51) 17.0 (@gain=30dB) dB RETURN LOSS Return Loss 10 dB ELECTRICAL Impedance 75 ? OPERATIONAL LED indicator Green DC Operating voltage 24 VDC DC Current consumption 45 mA CONNECTORS Number of inputs 1 Number of outputs 2 Connector Type F-female MECHANICAL Product Height 115 mm Product Depth 60 mm Product Width 107 mm Colour RAL 7016 - Anthracite grey Packing QTY 1 Packaging Height 0,060 m Packaging Width 0,120 m Packaging Depth 0,110 m Packaging Volume 0,001 m3 Net Weight 0,230 kg Tara Weight 0,025 kg Total Weight 0,255 kg -
Add to cartKit consisting of:
Ref. 561521: Amplificateur NanoKom, 3 entr?es: BIII/UHF-FMcoupl?-BIScoupl? ? ?
Amplificateur de m?t qui amplifie et couple les signaux de television terrestre et satellite provenant de diff?rentes antennes.
Il poss?de 3 entr?es: Les signaux BIII/UHF sont amplifi?s alors que la FM et la BIS (SAT) sont uniquement coupl?s.
Passage de courant sur l’entr?e satelllite pour alimenter le LNB.
Ref. 5796: PicoKom power supply (for FImix) 12V – 220mA, 1 output
12V (220mA) source, which sends power through the input coaxial cable, allowing the TV signal to pass through. It is sandwiched in the installation to power mast amplifiers or a BOSS system. It is compatible with amplifiers with satellite mixing (FImix), as it automatically detects the existence of an LNB management signal (voltage and tone) generated by a receiver at its output, and lets it pass to its input.
Stands out for
They incorporate “USOS” (User Selectable Output Signal) technology: the installer selects the desired output level, which remains stable. The device adjusts automatically to adapt its gain to variations in the input signal.
Separate amplification and very low noise figure, thus respecting the signal quality
Ultra-slim ergonomic design
EasyF connection system
They can be powered from 12 to 24V
Fully automated manufacturing subjected to rigorous quality controls
High armor chassis, made of Zamak
Main Features
LTE700 / 5G filter to eliminate telephony interference
ON / OFF switch to allow DC through to UHF input, to power a BOSS system
Simple assembly. Flange for fixing to the mast included
Durable orange ABS plastic housing for outdoor installation
EasyF connection system: simplicity and savingsThe EasyF is an innovative concept of connection of the internal conductor of the coaxial (live) cable, which is inserted directly into the device increasing the reliability of the connection. Furthermore, thanks to the absence of “F” connectors, it is possible to reduce the chassis and secure the connection of two cables with a single screw.
Real time savings: speeding up the installation is possible, as it is not necessary to make the connectorization of the coaxial cables. In addition, the process of threading the connectors on the device is avoided, which is sometimes complicated when space is not enough.
Connection reliability: the cable tie that holds the cables prevents the coaxial from loosening
Cost savings: no additional connector (neither “F” nor “CEI”) is required
Space optimization: inputs and outputs are always located on the same side of the device, avoiding bending the coaxial cables and facilitating work inside cabinets and registers
Very simple assembly in three steps: you only need to screw and unscrew the covers to connect two cables:
1. Unscrew the cover of the device to access the connection
2. Insert the previously stripped coaxial cables
3. Close the cover and screw to secure the connection
Find out more about the reliability of the EasyF system
With EasyF, the connection of the coaxial cable in the device is made by means of an automated system of insertion of the live (internal conductor) by contact, without requiring soldering.
Like the first day: the life of the device increases by eliminating the possible deterioration of the welds with the passage of time
Reduced failure rate: generally caused by cold welding
Optimization of electromagnetic behavior: at high frequencies
Reinforcement of our commitment to the environment: pollution caused by the welding process is eliminated and electricity consumption in production is reduced -
Add to cartKit consisting of:
Ref. 561621: NanoKom mast amplifier, 3 inputs: UHF-VHFmix-FImix
Mast-mounted amplifier to amplify and mix terrestrial and satellite television signals from various antennas.
It consists of 3 inputs: the signal is amplified at the UHF input, while the VHF and IF (SAT) input are only mixed.
Allows DC pass to the satellite input to power the LNB.
Ref. 5796: PicoKom power supply (for FImix) 12V – 220mA, 1 output
12V (220mA) source, which sends power through the input coaxial cable, allowing the TV signal to pass through. It is sandwiched in the installation to power mast amplifiers or a BOSS system. It is compatible with amplifiers with satellite mixing (FImix), as it automatically detects the existence of an LNB management signal (voltage and tone) generated by a receiver at its output, and lets it pass to its input.
Stands out for
They incorporate “USOS” (User Selectable Output Signal) technology: the installer selects the desired output level, which remains stable. The device adjusts automatically to adapt its gain to variations in the input signal.
Separate amplification and very low noise figure, thus respecting the signal quality
Ultra-slim ergonomic design
EasyF connection system
They can be powered from 12 to 24V
Fully automated manufacturing subjected to rigorous quality controls
High armor chassis, made of Zamak
Main Features
LTE700 / 5G filter to eliminate telephony interference
ON / OFF switch to allow DC through to UHF input, to power a BOSS system
Simple assembly. Flange for fixing to the mast included
Durable orange ABS plastic housing for outdoor installation
EasyF connection system: simplicity and savingsThe EasyF is an innovative concept of connection of the internal conductor of the coaxial (live) cable, which is inserted directly into the device increasing the reliability of the connection. Furthermore, thanks to the absence of “F” connectors, it is possible to reduce the chassis and secure the connection of two cables with a single screw.
Real time savings: speeding up the installation is possible, as it is not necessary to make the connectorization of the coaxial cables. In addition, the process of threading the connectors on the device is avoided, which is sometimes complicated when space is not enough.
Connection reliability: the cable tie that holds the cables prevents the coaxial from loosening
Cost savings: no additional connector (neither “F” nor “CEI”) is required
Space optimization: inputs and outputs are always located on the same side of the device, avoiding bending the coaxial cables and facilitating work inside cabinets and registers
Very simple assembly in three steps: you only need to screw and unscrew the covers to connect two cables:
1. Unscrew the cover of the device to access the connection
2. Insert the previously stripped coaxial cables
3. Close the cover and screw to secure the connection
Find out more about the reliability of the EasyF system
With EasyF, the connection of the coaxial cable in the device is made by means of an automated system of insertion of the live (internal conductor) by contact, without requiring soldering.
Like the first day: the life of the device increases by eliminating the possible deterioration of the welds with the passage of time
Reduced failure rate: generally caused by cold welding
Optimization of electromagnetic behavior: at high frequencies
Reinforcement of our commitment to the environment: pollution caused by the welding process is eliminated and electricity consumption in production is reduced -
Add to cartMast Amplifier Kit for DTT composed of amplifier 561721 and power supply 5795. NanoKom mast amplifier, 3 inputs: UHF-UHF-VHFmix. PicoKom power supply, 24V – 130mA, 2 outputs
-
SmartKom LTE700 Televes smart mast amplifier
KSh50,340.00Add to cartSmartKom Intelligent Mast Amplifier with Autoprogramming. 4e/1s ?EasyF?: 3x(VHF/UHF)[dc]-FMmix G 45-(-1)dB Vs 85dB?V. Includes Home Power Supply 2e/1s ?F? 12V-800mA, with Bluetooth antenna.
-
Add to cartMast Preamps with LTE 700 and 800 MHz Protection – 24 VDC
TRIAX electronic products include a range of mast preamps with high-performance, easy-to-mount F-connectors. The MFA series includes multiband preamps with 1-2-3 inputs and 1-2 outputs, with channel cut-off to LTE 700 and 800 signals (Ch 49 … 69 & Ch 60 … 69)
Characteristics
24 VDC power supply
LTE protection (LTE versions 700 and 800)
High output level
High resistance to external disturbances
High resistance to the corrosion
Optimized mechanism for easy installation
Neoprene cable clamp
Weather resistant housing
Tool for F connector included
RF protection and CE approval (EN50083)
Specifications
Characteristics
Kind Amplifiers – Mast
Output level max. (@ -60dB IMD) 108 dB?V
Frequency range
Band FM / VHF / UHF
[Input 1] – frequency 470 … 694 MHz
[Input 1] – channels 21 … 48
[Input 2] – frequency 87 … 108 MHz
[Input 2] – channels FM
[Input 3] – frequency 174 … 230 MHz
[Input 3] – channels DAB
LTE protection @ 700Mhz
Gain
[Input 1] – gain 20 … 35 dB
[Input 1] – noise figure 2.5 (@ 174 … 230MHz) 2.0 (@ 470 … 694Mhz) dB
[Input 2] – gain 10 … 22 dB
[Input 2] – noise figure 2.5 dB
[Input 3] – gain 10 … 22 dB
[Entry 3] – noise figure 2.5 dB
Lost
Rejection @ 714 MHz (Ch. 51) 17.0 (@ gain = 30dB) dB
Return loss
Return losses 10 dB
Electrical data
Impedance 75 ?
Operational
LED indicator Green
DC working voltage 24 VDC
Voltage consumption 42 mA
Connectors
Number of entries 3
Number of outputs 1
Mechanical
Colour RAL 7016 – Anthracite gray
Packaging Qty 1
Height 57 mm
Width 140 mm
Depth 113 mm
Packing Height 0.062 m
Packaging Width 0.140 m
Packing Depth 0.120 m
Packaging Volume 0.001 m3
Net weight 0.246 kg
Tare weight 0.040 kg
Total weight 0.286 kg -
Triax MFC 109 LTE 700 – Mast Amplifier (V+H+FI)
KSh4,428.00Add to cartThe MFC 109 LTE 700 is a mast-mount amplifier, powered via coaxial drop cable, covering the VHF (DAB), UHF and IF (SAT) bands in step. Its circuit is adapted to amplify the analog and digital terrestrial signals, mixing these with the IF signals through a low loss combiner, and allowing the passage of current to feed the LNB.
It has an LTE 700 filter to cut the range of channels from 49 to 59 whose frequencies (694 – 790 MHz) have been assigned for mobile communications services (LTE / 5G). It has 3 inputs: VHF (DAB), UHF and SAT and a single high-level output 104 dB?V.
Characteristics
Plastic box made of materials resistant to atmospheric agents.
Complies with RED regulations.
LED indicator of operation.
Adjustable gain.
Low noise figure.
12 to 24 Vdc power supply.
Pass current (max 400 mA) to supply the LNB
Simple and easy pole or wall mounting.
Specifications
Product MFC 109 LTE 700
Number of inputs / outputs 3/1
Entrance 1Band
Frequency
Channel
MHz
UHF
470 – 694
21 – 48
Entry 2
Band
Frequency
Channel
MHz
BI / BII / DAB
47 – 68/174 – 230
5 – 12
Entrance 3
Band
Frequency
Channel
MHz
SAT
950 – 2400
Gain
BI + FM + BIII
UHF
SAT
dB
dB
dB
7 – 22
15 – 30
-5.5
Noise figure
BI + FM + BIII
UHF
dB
dB
2.8
1.8
Max. Output level
@ -60dB IMA3
dB?V 104
Supply voltage VDC 12 – 24
LED indicator Green Yes
Connectors F-female
Weight Kg 0.205
DimensionsHigh or tall
Depth
Broad
mm
mm
mm
95
Four. Five
145
-
Add to cartTOS 04F, 4-way PLC Splitter FC/PC?
The balanced coupler is implemented in a valid metal housing
pre-assembled with FC/PC connectors
PLC (Planar Lightwave Circuit) couplers with a wide window of wave lengths
Low and flat insertion loss
Specifications
CHARACTERISTICS
Type OPTO Coupler balanced
Coupling Ratio (OPTO) 4x 12.5 %
Wavelength 1260…1650 nm
LOSS
Insertion loss (typ.) 7.2 dB
CONNECTORS
Connector Type Optical – FC/PC
Number of inputs 1
Number of outputs 4
MECHANICAL
Dimensions product (H x D x W) 150x20x114 mm
Packing QTY 1
Packaging Height 0,045 m
Packaging Width 0,155 m
Packaging Depth 0,215 m
Packaging Volume 0,001 m3
Net Weight 0,234 kg
Tara Weight 0,064 kg
Total Weight 0,298 kg -
Add to cartTOS 08F, 8-way PLC Splitter FC/PC?
The balanced coupler is implemented in a valid metal housing
pre-assembled with FC/PC connectors
PLC (Planar Lightwave Circuit) couplers with a wide window of wave lengths
Low and flat insertion loss
Specifications
CHARACTERISTICS
Type OPTO Coupler balanced
Coupling Ratio (OPTO) 8x 12.5 %
Wavelength 1260…1650 nm
LOSS
Insertion loss (typ.) 10.2 dB
CONNECTORS
Connector Type Optical – FC/PC
Number of inputs 1
Number of outputs 8
MECHANICAL
Dimensions product (H x D x W) 150x20x114 mm
Packing QTY 1
Packaging Height 0,045 m
Packaging Width 0,153 m
Packaging Depth 0,213 m
Packaging Volume 0,001 m3
Net Weight 0,286 kg
Tara Weight 0,064 kg
Total Weight 0,350 kg -
Add to cartHigh corrosion resistance steel mast, thanks to its dual galvanized treatment and reactive sealing (RPR). Its grooved design allows it to be assembled and fixed with other poles to extend its length. RPR mast 2m long, diameter ?40mm and thickness 1.25mm. Televes 3041
Popular Products
-
ZX5SE Morley 1-5 Loop Control Panel
-
X-DA4125EN Honeywell High Efficiency Power Amplifier
KSh248,594.99
-
X-DA4125 Honeywell Class D Digital Power Amplifier
KSh277,887.00
-
X-DA4060 Honeywell High Efficiency Power Amplifier
KSh190,008.00
-
X-DA2250 Honeywell High Efficiency Power Amplifier
KSh261,261.00
Products
-
ZX5SE Morley 1-5 Loop Control Panel
-
X-DA4125EN Honeywell High Efficiency Power Amplifier
KSh248,594.99
-
X-DA4125 Honeywell Class D Digital Power Amplifier
KSh277,887.00
-
X-DA4060 Honeywell High Efficiency Power Amplifier
KSh190,008.00
-
X-DA2250 Honeywell High Efficiency Power Amplifier
KSh261,261.00