Category: TV Distribution
TV Distribution
Showing 81–160 of 1858 results
-
Read more5G filter**Televes 403210**with CEI connector
LTE2 filter to adapt your DTT equipment (TV / Receiver) to the 2nd Digital Dividend. This low pass filter with cut on channel 48 eliminates all interference caused by 5G signals.
With this filter you can enjoy the new UHF frequency band 47-694 MHz without interference as it attenuates unwanted signals up to 25dB.
Small size filter with an elongated shape in plug-in format to connect directly to devices with CEI input to protect.
This filter has no DC current path.
-
Read moreLTE700 filter for the 5G EasyF channel 48
Televes 405202 filter to install on the antenna mast and eliminate interference with the 5G band. This is a high rejection low pass filter with cutoff frequency on channel 48. The equipment has low through attenuation to affect as little as possible the distributed signal.
Small size filter, protected with a rugged ABS plastic hood designed for outdoor use Its EasyF connection system facilitates installation and does not require connectors.
-
Read moreLTE2 Outdoor Televes 405203 Filter
LTE 5G mast filter to adapt your DTT antenna to the 2nd Digital Dividend. This high rejection low pass filter attenuates all the signals that generate interference, making the cut on channel 48 (694 MHz).
It allows the passage of DC current to power the UHF antenna if it is active. It includes the outer chest made of ABS plastic to protect the equipment from the weather. The connections of this filter are “EasyF” flange type to reduce its size and facilitate the connection of the coaxial cable. The flange connections do not use connectors, the coaxial cable is inserted stripped and fastened with a screw.
It is always recommended to install the filter prior to the amplifier of the UHF signal so that it only amplifies the desired signals.
-
Read moreVelcro Tape 8 Meters for Cable Organization Televes 200101
Velcro-type nylon roll of 8 meters and 15mm wide, black, for holding and organizing any type of cable: coaxial, data or fiber optic.
Firm and secure hold by adhering one surface of the tape to the other. Quick placement and easy separation to reuse as many times as necessary thanks to its velcro system.
It can be cut with conventional scissors to the required length.
**
-
Read moreTeleves 8 Outputs CATV Terminal Shunt F 13dB Connector
8-output F-type shunt with 13dB attenuation for terrestrial signals (5-1220 MHz), compatible with Docsis 3.1 coaxial cable data technology. It does not include DC power pass-through. This type of shunt is used at the end of the distribution, as it has no feed-through losses.
This shunt is used in indoor installations, for wall mounting, rack mounting or standard DIN rail mounting.
It has a high efficiency, comes with a chassis made of zamak, which provides a great shielding. It is compatible with DOCSIS 3.1, which is an international standard that defines the requirements needed to achieve the highest possible speed in data transmission over cable networks.
This shunt is not suitable for satellite signal distribution.
-
Read moreTeleves 8 Outputs CATV F Connector 20dB shunt
8-output F-type shunt with 20dB attenuation for terrestrial signals (5-1220 MHz), compatible with Docsis 3.1 coaxial cable data technology. It does not include DC power pass-through.
This shunt is used in indoor installations, for wall, rack or standard DIN rail mounting.
It has a high efficiency, comes with a chassis made of zamak, which provides a great shielding. It is compatible with DOCSIS 3.1, which is an international standard that defines the requirements needed to achieve the highest possible speed in data transmission over cable networks.
This shunt is not suitable for satellite signal distribution.
-
Read moreTeleves 8 Outputs CATV shunt F Connector 23dB
8-output F-type shunt with 23dB attenuation for terrestrial signals (5-1220 MHz), compatible with Docsis 3.1 coaxial cable data technology. It does not include DC power pass-through.
This shunt is used in indoor installations, for wall, rack or standard DIN rail mounting.
It has a high efficiency, comes with a chassis made of zamak, which provides a great shielding. It is compatible with DOCSIS 3.1, which is an international standard that defines the requirements needed to achieve the highest possible speed in data transmission over cable networks.
This shunt is not suitable for satellite signal distribution.
-
Read moreTeleves 8 Outputs CATV shunt F connector 17dB
8-output F-type shunt with 17dB attenuation for terrestrial signals (5-1220 MHz), compatible with Docsis 3.1 coaxial cable data technology. It does not include DC power pass-through.
This shunt is used in indoor installations, for wall, rack or standard DIN rail mounting.
It has a high efficiency, comes with a chassis made of zamak, which provides a great shielding. It is compatible with DOCSIS 3.1, which is an international standard that defines the requirements needed to achieve the highest possible speed in data transmission over cable networks.
This shunt is not suitable for satellite signal distribution.
-
Read more8D EasyF tap-off, 16dB with Televes 5610 flange
Derivator with 8 derivations and EasyF connection system, for SMATV signals.
It has a compact design and efficient electronic behavior.
It is easy to install and saves on assembly thanks to the EasyF.
It is made of Zamak which provides great shielding and great reliability.
Includes grounding screw.
-
Read moreConnection accessory adapter 5/8-F. .. Ref 4123 Televes
Accessory Adapter Connection 5/8-F -
Read moreCompatible with SpaceHD REC-DSD300-HD-S2
Receiver, and also works with DStv series 4, 5 and 6 decoders.Product code: PSU-DSD300
-
Adapter “F Quick” male – male (Box 50 units) Televes
KSh24,684.00Add to cartAdapter that allows the connection of two female F connectors together, usually with the purpose of connecting two products equipped with F connections. The Quick F range connector does not need to be screwed on.**Professional plastic box of 50 units. Televes 3821
-
Adapter 5/8″ Male – “F” Female Televes
KSh3,300.00Add to cartAdapter that allows converting an “F” connection into 5/8″ and vice versa.**Televes 4123
-
Read moreAdapter double Easy F male to F female Televes
The adapter 405701 of Televes is an adapter made in Zamak, which allows converting a double “EasyF” connection into two female “F” type connections.
With this adapter we can connect a cable with type F connection in a distributor or connection adapter Easy F or flange type.
In addition, thanks to its manufacture in Zamak makes it an adapter resistant to the passage of time.
-
Adapter F Female – F Female (Box 50 units) Televes
KSh21,660.00Add to cartF female – female adapter. With narrow thread and length 27mm. Adapter that allows two male “F” connectors to be connected to each other, typically two coaxial extensions. Does not include nut or washer. Supplied in a professional plastic box of 50 units.
-
-
Adapter F female – F female Televes
KSh738.00Add to cartF adapter female – F female. It is usually used to join two coaxial cables that have type F connector and also extend coaxial cables. Televes 4307
-
Add to cartAdapter SFP 10Gb Ethernet LC/PC 2 fibers that generates an interface to make OLT inputs and outputs compatible with different types of networks. Televes 769412
-
Add to cartAdapter**Gb Ethernet RJ45 that generates an interface to make OLT inputs and outputs compatible with different types of networks. Televes 769411
-
Add to cartAdapter Class B GPON + 1 SC/PC fiber that generates an interface to make OLT inputs and outputs compatible with different types of networks. Televes 769410
-
Add to cartAdapter Class C GPON + 1 SC/PC fiber that generates an interface to make OLT inputs and outputs compatible with different types of networks. Televes 769413
-
-
Read more1-25dB IEC Adjustable Dimmer
This 4315 Televes attenuator allows you to reduce the level of DTT signal on the TV when interference from excessive powers occurs.
The dimmer allows the passage of DC current to power active components of the terrestrial installation that require it.
-
Alcad AI-100 Indoor amplifier 1+1 outputs
KSh8,512.00Add to cartAlcad AI-100 – Serie 904: Indoor amplifier 1+1 outputs.
Broadband apartment amplifier for terrestrial TV, with built-in power supply unit. It amplifies the VHF and UHF bands separately and has an independent gain control for each band. It includes two outputs to make the distribution to two or more televisions. The outputs are equal or unbalanced.
Applications
Designed to enlarge analogue and digital terrestrial TV installations within an apartment or house. It amplifies the TV signal so a distribution with several new outlets can be made from the signal of one TV outlet or from the coaxial cable entering the house. The levels are easily adjusted by means of the two gain controls.
Characteristics
Made from ABS plastic, with an internal zamak chassis which gives maximum shielding. The power supply unit is insulated from the rest of the high frequency circuit, complying with the safety regulations for the installer and the user. Fixed to the wall by means of the supplied screwsand wall-plugs. F type connectors.
Downloads
Technical specification
Technical specification
Manuals
– pdf 146.32 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad AI-133 Indoor amp 1 output catv rp 65 mhz
KSh10,358.00Add to cartAlcad AI-133 – Serie 904: Indoor amp 1 output catv rp 65 mhz.
Broadband apartment amplifier for terrestrial TV, with built-in power supply unit. It amplifies the VHF and UHF bands separately and has an independent gain control for each band. It includes two outputs to make the distribution to two or more televisions. The outputs are equal or unbalanced.
Applications
Designed to enlarge analogue and digital terrestrial TV installations within an apartment or house. It amplifies the TV signal so a distribution with several new outlets can be made from the signal of one TV outlet or from the coaxial cable entering the house. The levels are easily adjusted by means of the two gain controls.
Characteristics
Made from ABS plastic, with an internal zamak chassis which gives maximum shielding. The power supply unit is insulated from the rest of the high frequency circuit, complying with the safety regulations for the installer and the user. Fixed to the wall by means of the supplied screws and wall-plugs. F type connectors.
Downloads
Technical specification
Technical specification
Manuals
– pdf 202.61 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad AI-223 Indoor ampl 2 outputs catv (rp 65mhz)
KSh10,114.00Add to cartAlcad AI-223 – Serie 904: Indoor ampl 2 outputs catv (rp 65mhz).
Broadband apartment amplifier for terrestrial TV, with built-in power supply unit. It amplifies the VHF, UHF and interband bands continuously and includes a return path. It has a gain control and two outputs for the distribution to two or more televisions.
Applications
Designed to enlarge analogue and digital terrestrial TV installations within a house. Especially appropriate as an apartment amplifier in cable TV networks or in community installations where the interband bands are used. It amplifies the TV signal so a new distribution can be made from the signal of one TV outlet or from the coaxial cable entering the house.
Characteristics
Made from ABS plastic, with an internal zamak chassis which gives maximum shielding. The power supply unit is insulated from the rest of the high frequency circuit. Fixed to the wall by means of the supplied screws and wall-plugs. F type connectors.
Downloads
Technical specification
Technical specification
Manuals
– pdf 198.58 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad AI-240 Indoor amplifier 2 outputs lte800
KSh8,996.00Add to cartAlcad AI-240 – Serie 904: Indoor amplifier 2 outputs lte800.
Broadband apartment amplifier for terrestrial TV, with built-in power supply unit. It amplifies the VHF and UHF bands separately and has an independent gain control for each band. It incorporates a filter to reject the LTE800 band. It includes two symmetrical outputs to make the distribution to two or more televisions.
Applications
Designed to enlarge analogue and digital terrestrial TV installations within an apartment or house. It amplifies the TV signal so a distribution with several new outlets can be made from the signal of one TV outlet or from the coaxial cable entering the house. The levels are easily adjusted by means of the two gain controls. The amplifier prevents possible interferences generated by devices operating in the LTE800 band.
Characteristics
Made from ABS plastic, with an internal zamak chassis which gives maximum shielding. The power supply unit is insulated from the rest of the high frequency circuit, complying with the safety regulations for the installer and the user. Fixed to the wall by means of the supplied screws and wall-plugs. F type connectors.
Downloads
Technical specification
Technical specification
Manuals
– pdf 105.84 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
Technical specifications
-
Alcad AI-271 Indoor amplifier 2 outputs lte700
KSh9,902.00Add to cartAlcad AI-271 – Serie 904: Indoor amplifier 2 outputs lte700.
Broadband apartment amplifier for terrestrial TV, LTE700 compatible, with built-in power supply unit. It amplifies the VHF and UHF bands separately and has an independent gain control for each band. It includes two outputs to make the distribution to two or more televisions.
Applications
Designed to enlarge analogue and digital terrestrial TV installations within an apartment or house. It amplifies the TV signal so a distribution with several new outlets can be made from the signal of one TV outlet or from the coaxial cable entering the house. The levels are easily adjusted by means of the two gain controls.
Characteristics
Fresh look, with a case made of ABS plastic for better impact resistance, with an internal zamak chassis which gives maximum shielding and extended range power supply. Easy wall fixing thanks to the supplied screwsand wall-plug or, alternatively, DIN rail installation by means of an adapter (not supplied). F type connectors.
Downloads
Technical specification
Technical specification
Manuals
AI-271 Manual pdf 788.59 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE Declaration – AI-271 pdf 149.8 KB
Flyers
AI-201 & AI-271 flyer pdf 1.09 MB
Technical specifications
-
Alcad AI-400 Indoor amplifier 4 outputs
KSh11,012.00Add to cartAlcad AI-400 – Serie 904: Indoor amplifier 4 outputs.
Broadband apartment amplifier for terrestrial TV, with built-in power supply unit. It amplifies the VHF and UHF bands separately and has an independent gain control for each band. It includes four outputs to make the distribution to 4 or more televisions. The outputs are equal or unbalanced.
Applications
Designed to enlarge analogue and digital terrestrial TV installations within an apartment or house. It amplifies the TV signal so a distribution with several new outlets can be made from the signal of one TV outlet or from the coaxial cable entering the house. The levels are easily adjusted by means of the two gain controls.
Characteristics
Made from ABS plastic, with an internal zamak chassis which gives maximum shielding. The power supply unit is insulated from the rest of the high frequency circuit, complying with the safety regulations for the installer and the user. Fixed to the wall by means of the supplied screws and wall-plugs. F type connectors.
Downloads
Technical specification
Technical specification
Manuals
– pdf 198.58 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad AI-414 Indoor amp tv+if 4 outputs dc path
KSh14,822.00Add to cartAlcad AI-414 – Serie 904: Indoor amp tv+if 4 outputs dc path.
Broadband apartment amplifier for terrestrial and satellite TV for installation with multiswitches, with 4 inputs and built-in powern supply unit. It amplifies the terrestrial TV and IF satellite bands separately. It has an independent gain control for each band and a fixed slope on the FI band.
Applications
Designed to enlarge analogue and digital terrestrial and satellite TV installations within an apartment or house. It amplifies the terrestrial and satellite TV signals from the output of the multiswitch so a distribution with TV-SAT outlets can be made. The levels are easily adjusted by means of the two built-in gain controls.
Characteristics
Made from ABS plastic, with an internal zamak chassis which gives maximum shielding. The power supply unit is insulated from the rest of the high frequency circuit. Fixed to the wall by means of the supplied screws and wall-plugs. F type connectors.
Downloads
Technical specification
Technical specification
Manuals
– pdf 330.82 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad AL-100 Power supply 24 vdc 100 ma
KSh7,078.00Add to cartAlcad AL-100 – Serie 903: Power supply 24 vdc 100 ma.
Power supply units for mast amplifiers, 24 voltages. The power supply unit converts the mains supply into DC voltage and injects it into the coaxial cable to feed the amplifier. The signal coming from the antenna is distributed to its outputs. The power supply unit is available with two, four or five outputs. The power supply units are protected against overloads and short circuits. Available on request in 125 or 240 .
Applications
Individual digital and analogue terrestrial TV installations where mast amplifiers or antenna box preamplifiers are used. The feed voltage should be selected according to the amplifier installed.
Characteristics
Shielded zamak chassis, covered by an ABS plastic box for outdoor use. Power supply unit insulated from the high frequency circuit, complying with safety standards for both the installer and the user. Fixed to the wall by means of supplied wallplugs and screws. F type connectors. Supplied in individual or multiple packs.
Accessories
9120039 CM-004 Male F connector for **6.6 mm coaxial cable 9080023 MC-302 Male F connector for **7.0mm coaxial cable. 9120011 RS-275 Type F load of 75 ****. 9040078 DI-007 DIN rail adaptor
Downloads
Technical specification
Technical specification
Manuals
– pdf 130.03 KB
– pdf 178.25 KB
– pdf 141.19 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems_AL-BO pdf 34.29 KB
Technical specifications
-
Alcad AL-105 Power supply 12 vdc 100 ma
KSh6,226.00Add to cartAlcad AL-105 – Serie 903: Power supply 12 vdc 100 ma.
Power supply units for mast amplifiers, 12 voltages. The power supply unit converts the mains supply into DC voltage and injects it into the coaxial cable to feed the amplifier. The signal coming from the antenna is distributed to its outputs. The power supply units are protected against overloads and short circuits. Available on request in 125 or 240 .
Applications
Individual digital and analogue terrestrial TV installations where mast amplifiers or antenna box preamplifiers are used. The feed voltage should be selected according to the amplifier installed.
Characteristics
Shielded zamak chassis, covered by an ABS plastic box for outdoor use. Power supply unit insulated from the high frequency circuit, complying with safety standards for both the installer and the user. Fixed to the wall by means of supplied wallplugs and screws. F type connectors. Supplied in individual or multiple packs.
Accessories
9120039 CM-004 Male F connector for **6.6 mm coaxial cable 9080023 MC-302 Male F connector for **7.0mm coaxial cable. 9120011 RS-275 Type F load of 75 ****. 9040078 DI-007 DIN rail adaptor.
Downloads
Technical specification
Technical specification
Manuals
– pdf 178.25 KB
– pdf 173.26 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems_AL-BO pdf 34.29 KB
Technical specifications
-
Add to cartAlcad AL-110 – Serie 903: Power supply 24 vdc 100ma, 4 outputs.
Power supply units for mast amplifiers, 24 voltages. The power supply unit converts the mains supply into DC voltage and injects it into the coaxial cable to feed the amplifier. The signal coming from the antenna is distributed to its outputs. The power supply unit is available with two, four or five outputs. The power supply units are protected against overloads and short circuits. Available on request in 125 or 240
Applications
Individual digital and analogue terrestrial TV installations where mast amplifiers or antenna box preamplifiers are used. The feed voltage should be selected according to the amplifier installed. Characteristics Shielded zamak chassis, covered by an ABS plastic box for outdoor use. Power supply unit insulated from the high frequency circuit, complying with safety standards for both the installer and the user. Fixed to the wall by means of supplied wallplugs and screws. F type connectors. Supplied in individual or multiple packs.
Accessories
9120039 CM-004 Male F connector for **6.6 mm coaxial cable 9080023 MC-302 Male F connector for **7.0mm coaxial cable. 9120011 RS-275 Type F load of 75 ****. 9040078 DI-007 DIN rail adaptor
Downloads
Technical specification
Technical specification
Manuals
– pdf 178.25 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad AL-245 Power supply 12/13/18 vdc 400 ma
KSh7,402.00Add to cartAlcad AL-245 – Serie 903: Power supply 12/13/18 vdc 400 ma.
Power supply unit for mast amplifier with SAT multiplexing. Voltage supply 12Vdc. If LNB control signal is received it powers both the amplifier and the LNB with the control signal comming from the SAT receiver. The output voltage is injected into the coaxial cable to power the amplifier and the LNB. The signal coming from the antenna is distributed to its two outputs. Protected against overloads and short circuits.
Applications
Individual terrestrial ans satellite TV installations, digital and analogue, where mast amplifiers with SAT multiplexing are used.
Characteristics
Shielded zamak chassis, covered by an ABS plastic box. Power supply unit insulated from the high frequency circuit, complying with safety standards for both the installer and the user. Fixed to the wall by means of supplied wallplugs and screws. F type connectors.
Downloads
Technical specification
Technical specification
Manuals
AL-245 HN pdf 824.47 KB
AL-245 Manual pdf 991.42 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE Declaration – AL-245 pdf 71 KB
Technical specifications
-
Add to cartAlcad ALC-290 – Serie 962: Power supply 48v dc 65.3 va 100-240 vac.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_DES pdf 5.85 MB
Certificates
DEC_ALC-290 pdf 92.93 KB
Technical specifications
-
Alcad AM-190 Amp uhf 20 db lte700 mast 24 vdc
KSh6,912.00Add to cartAlcad AM-190 – Serie 903: Amp uhf 20 db lte700 mast 24 vdc.
Broadband amplifiers for masts, compatible with LTE700 and LTE800 mobile telephone signals with amplification band in UHF 470-694 MHz. They have one input to amplify and combine the signals from the antennas. They are fed through the coaxial cable from a power supply unit installed inside the building. They incorporate a switchable DC path, allowing power to be supplied to a preamplifier.
Applications
Individual digital and analogue terrestrial TV installations which are affected by the transmission of LTE700 and LTE800 mobile phone signals and which require low gain. They amplify and mix the signals from several antennas. The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, covered by a weather-resistant plastic casing. Easy to open and close, the chassis can be tilted to facilitate manipulation. It can be installed either on a mast, by means of a polyamide clamp, or on a wall. Resistant to sun and water (IP53). Greater insulation between inputs and outputs. F-type connectors for screwing or crimping.
Accessories
9030086 AL-100 24 power supply unit. 9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm. 9080030 MC-304 Male compression F connector for RG-6 coaxial, **7.0 mm
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
-
Alcad AM-195 Amp uhf 32 db lte700 mast 24 vdc
KSh7,648.00Add to cartAlcad AM-195 – Serie 903: Amp uhf 32 db lte700 mast 24 vdc.
Broadband amplifiers for masts, compatible with LTE700 mobile telephone signals with amplification band in UHF 470-694 MHz. They have one input to amplify and combine the signals from the antennas. They are fed through the coaxial cable from a power supply unit installed inside the building. They incorporate a switchable DC path, allowing power to be supplied to a preamplifier.
Applications
Individual digital and analogue terrestrial TV installations which are affected by the transmission of LTE700 mobile phone signals and which require low gain. They amplify and mix the signals from several antennas. The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, covered by a weather-resistant plastic casing. Easy to open and close, the chassis can be tilted to facilitate manipulation. It can be installed either on a mast, by means of a polyamide clamp, or on a wall. Resistant to sun and water (IP53). Greater insulation between inputs and outputs. F-type connectors for screwing or crimping.
Accessories
9030086 AL-100 24 power supply unit. 9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm. 9080030 MC-304 Male compression F connector for RG-6 coaxial, **7.0 mm
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
Technical specifications
-
Add to cartAlcad AM-292 – Serie 903: Amp uhf-dab/fm 20 db lte700 mast 24 vdc.
Broadband amplifiers for masts, compatible with LTE700 and LTE800 mobile telephone signals with amplification band in UHF 470-694 MHz. They have two inputs to amplify and combine the signals from the antennas. They are fed through the coaxial cable from a power supply unit installed inside the building. They incorporate a switchable DC path, allowing power to be supplied to a preamplifier.
Applications
Individual digital and analogue terrestrial TV installations which are affected by the transmission of LTE700 and LTE800 mobile phone signals and which require low gain. They amplify and mix the signals from several antennas. The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, covered by a weather-resistant plastic casing. Easy to open and close, the chassis can be tilted to facilitate manipulation. It can be installed either on a mast, by means of a polyamide clamp, or on a wall. Resistant to sun and water (IP53). Greater insulation between inputs and outputs. F-type connectors for screwing or crimping.
Accessories
9030086 AL-100 24 power supply unit. 9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm. 9080030 MC-304 Male compression F connector for RG-6 coaxial, **7.0 mm. CODE 9030165 9030166 9030172
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
-
Add to cartAlcad AM-296 – Serie 903: Amp uhf-dab/fm 32 db lte700 mast 24 vdc.
Broadband amplifiers for masts, compatible with LTE700 and LTE800 mobile telephone signals with amplification band in UHF 470-694 MHz. They have three inputs to amplify and combine the signals from the antennas. They are fed through the coaxial cable from a power supply unit installed inside the building. They incorporate a switchable DC path, allowing power to be supplied to a preamplifier.
Applications
Individual digital and analogue terrestrial TV installations which are affected by the transmission of LTE700 and LTE800 mobile phone signals and which require high gain. They amplify and mix the signals from several antennas. The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, covered by a weather-resistant plastic casing. Easy to open and close, the chassis can be tilted to facilitate manipulation. It can be installed either on a mast, by means of a polyamide clamp, or on a wall. Resistant to sun and water (IP53). Greater insulation between inputs and outputs. F-type connectors for screwing or crimping.
Accessories
9030086 AL-100 +24 power supply unit. 9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm. 9080030 MC-304 Male compression F connector for RG-6 coaxial **7.0 mm.
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
Technical specifications
-
Alcad AM-309 Amp groups uhf-uhf-vhf/fm mast
KSh12,274.00Add to cartAlcad AM-309 – Serie 903: Amp groups uhf-uhf-vhf/fm mast.
Configurable amplifiers for masts. The UHF inputs can be configured by adding low pass, high pass, band pass, monochannel, band rejection and channel rejection filters. The filters are installed during the factory manufacturing process and cannot be readjusted by the user. The attenuator located at each input makes it possible to control the gain to obtain an output with all the bands equalised.
Applications
Individual digital and analogue terrestrial TV installations which require an amplifier adapted to the specific needs of the area. The interference from undesired channels can be avoided through the use of the built-in filters. The type of filter and the initial and final channels should be specified in the order.
Characteristics
Shielded zamak chassis, covered by an ABS plastic box for outdoor use. Fixed to the mast by means of a polyamide clamp. F-type connectors.
Accessories
9030086 AL-100 +24 power supply unit. 9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm.
Downloads
Technical specification
Technical specification
Manuals
– pdf 156.97 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
-
Alcad AM-396 Amp uhf-uhf-dab/fm 32 db lte700 mast
KSh11,020.00Add to cartAlcad AM-396 – Serie 903: Amp uhf-uhf-dab/fm 32 db lte700 mast.
Broadband amplifiers for masts, compatible with LTE800 and LTE700 mobile signals (UHF amplification in the 470-694 MHz band). They have three inputs to amplify and combine the signals from the antennas. They are fed through the coaxial cable from a power supply unit installed inside the building. They incorporate a switchable DC path, allowing power to be supplied to a preamplifier.
Applications
Individual digital and analogue terrestrial TV installations which are affected by the transmission of LTE mobile phone signals and which require high gain. They amplify and mix the signals from several antennas. The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, covered by a weather-resistant plastic casing. Easy to open and close, the chassis can be tilted to facilitate manipulation. It can be installed either on a mast, by means of a polyamide clamp, or on a wall. Resistant to sun and water (IP53). Greater insulation between inputs and outputs. F-type connectors for screwing or crimping.
Accessories
9030086 AL-100 +24 power supply unit. 9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm. 9080030 MC-304 Male compression F connector for RG-6 coaxial **7.0 mm.
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
Technical specifications
-
Add to cartAlcad AM-397 – Serie 903: Amp uhf-biii/dab-fm 32 db lte700 24 vdc.
Broadband amplifiers for masts, compatible with LTE700 and LTE800 mobile telephone signals with amplification band in UHF 470-694 MHz. They have three inputs to amplify and combine the signals from the antennas. They are fed through the coaxial cable from a power supply unit installed inside the building. They incorporate a switchable DC path, allowing power to be supplied to a preamplifier.
Applications
Individual digital and analogue terrestrial TV installations which are affected by the transmission of LTE700 and LTE800 mobile phone signals and which require high gain. They amplify and mix the signals from several antennas. The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, covered by a weather-resistant plastic casing. Easy to open and close, the chassis can be tilted to facilitate manipulation. It can be installed either on a mast, by means of a polyamide clamp, or on a wall. Resistant to sun and water (IP53). Greater insulation between inputs and outputs. F-type connectors for screwing or crimping.
Accessories
9030086 AL-100 +24 power supply unit. 9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm. 9080030 MC-304 Male compression F connector for RG-6 coaxial **7.0 mm.
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 232.44 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
DEC_AM_LTE700 pdf 65.95 KB
-
Add to cartAlcad AM-497 – Serie 903: Amp uhf-uhf-biii/dab-fm 32 db lte700 24v.
Broadband amplifiers for masts, compatible with LTE700 and LTE800 mobile telephone signals with amplification band in UHF 470-694 MHz. They have four inputs to amplify and combine the signals from the antennas. They are fed through the coaxial cable from a power supply unit installed inside the building. They incorporate a switchable DC path, allowing power to be supplied to a preamplifier.
Applications
Individual digital and analogue terrestrial TV installations which are affected by the transmission of LTE700 and LTE800 mobile phone signals and which require high gain. They amplify and mix the signals from several antennas. The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, covered by a weather-resistant plastic casing. Easy to open and close, the chassis can be tilted to facilitate manipulation. It can be installed either on a mast, by means of a polyamide clamp, or on a wall. Resistant to sun and water (IP53). Greater insulation between inputs and outputs. F-type connectors for screwing or crimping.
Accessories
9030086 AL-100 +24 power supply unit. 9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm. 9080030 MC-304 Male compression F connector for RG-6 coaxial **7.0 mm.
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 368.98 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
-
Alcad AM-696 Amp sat-uhf-dab/fm 32 db mat
KSh10,596.00Add to cartAlcad AM-696 – Serie 903: Amp sat-uhf-dab/fm 32 db mat.
Broadband amplifiers for masts, amplifies the signal from terrestrial antennas and multiplexes the satellite signal. Powered through the coaxial cable from a power supply unit installed inside the building. The LNB is controlled by the control signal comming from the satellite set-top-box. It incorporates a switchable DC path, allowing power to be supplied to an antenna preamplifier. Compatible with LTE700 and LTE800 mobile telephone signals. UHF Amplification band 470-694 MHz.
Applications
Individual terrestrial and satellite TV installations, digital and analogue. It amplifes the signal from two terrestrial antennas and combines the signals along with the satellite signal. The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, with a weather-resistant plastic casing. Easy to open and close, the chassis can be tilted to facilitate manipulation. It can be installed either on a mast, by means of a polyamide zip tie, or on a wall. Resistant to sun and water (IP53). F-type compression or screwing connectors.
Downloads
Technical specification
Technical specification
Manuals
AM-696 HN pdf 824.47 KB
AM-696 Manual pdf 991.42 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE Declaration – AM-696 pdf 71 KB
Technical specifications
-
Alcad AM-915 Amp uhf-dab 40 db lte700 mast
KSh7,800.00Add to cartAlcad AM-915 – Serie 903: Amp uhf-dab 40 db lte700 mast.
Broadband amplifiers for masts, compatible with LTE800 and LTE700 mobile signals (UHF amplification in the 470-694 MHz band). They have two inputs to amplify and combine the signals from the antennas. They have two outputs. They are fed through the coaxial cable from a power supply unit installed inside the building. They incorporate a switchable DC path, allowing power to be supplied to a preamplifier.
Applications
Individual digital and analogue terrestrial TV installations which are affected by the transmission of LTE mobile phone signals and which require very high gain. They amplify and mix the signals from several antennas. The signal obtained can be distributed to a large number of TV outlets by means of a single coaxial cable.
Characteristics
Shielded zamak chassis, covered by a weather-resistant plastic casing. Easy to open and close, the chassis can be tilted to facilitate manipulation. It can be installed either on a mast, by means of a polyamide clamp, or on a wall. Resistant to sun and water (IP53). Greater insulation between inputs and outputs. F-type connectors for screwing or crimping.
Accessories
9030086 AL-100 +24 power supply unit. 9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm. 9080030 MC-304 Male compression F connector for RG-6 coaxial **7.0 mm.
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 299.28 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
Technical specifications
-
Alcad AS-125 Power supply 24 vdc 1.7 a (230/240 vac)
KSh20,244.00Add to cartAlcad AS-125 – Serie 905: Power supply 24 vdc 1.7 a (230/240 vac).
Compact switching power supply units which permits the installation of up to 18 modules on the support frame.
Applications
Necessary to supply the amplification modules of the equipment. The number of modules which it can feed varies according to the consumption of the modules and of the consumption of the LNBs in the case of SAT amplifier modules.18 modules can be fed in the case of monochannel amplifiers.
Characteristics
Protected against overloads and short-circuits. Made from an aluminium profile and alvanised plate. It includes a protection fuse which the installer can access. Supplied with power cable with faston connector for IEC connector equipment.
Downloads
Technical specification
Technical specification
Manuals
– pdf 165.67 KB
– pdf 165.54 KB
– pdf 624.67 KB
– pdf 204.95 KB
– pdf 393.23 KB
– pdf 201.67 KB
– pdf 201.66 KB
– pdf 327.17 KB
– pdf 515.52 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad AU-620 Amplifier multiswitch 4 inputs
KSh39,122.00Add to cartAlcad AU-620 – Serie 913: Amplifier multiswitch 4 inputs.
SAT amplifier for 4, 8 or 16 polarities, for installations in cascade. For 16 polarities, two stacked amplifiers of 8 polarities are installed. Equipped with gain control and independent equaliser for each polarity. Requires the FU-513 power supply unit, from the NET power supply connector, to feed the amplifier and intermediate active multiswitches. To power the LNB, the FU-612 power supply unit is used.
Applications
Medium-sized to large MATV and SMATV installations. Enables distribution to up to 128 TV outlets in a single line, with a single amplifier and FU-513 power supply unit. By dividing the installation into lines of 128 outlets and distributing the 4 or 8 polarities and the terrestrial TV to all the lines, it is possible to reach more than 2,000 outlets. Amplifies and equalises all the polarities before the cascade of multiswitches.
Characteristics
Return path included from 5 to 65MHz. Shielded zamak chassis with plastic supports. F-type connectors. Two power supply jacks, 9.5mm x 2.1mm for the NET cascade and for the LNB.
Downloads
Technical specification
Technical specification
Manuals
AU-620 Manual pdf 796.9 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Distribution pdf 269.31 KB
Technical specifications
-
Alcad AU-621 Amplifier multiswitch 4 inputs 25 db
KSh37,218.00Add to cartAlcad AU-621 – Serie 913: Amplifier multiswitch 4 inputs 25 db.
SAT amplifier for 4, 8 or 16 polarities, for installations in cascade. For 16 polarities, two stacked amplifiers of 8 polarities are installed. Equipped with gain control and independent equaliser for each polarity. Requires the FU-513 power supply unit, from the NET power supply connector, to feed the amplifier and intermediate active multiswitches. To power the LNB, the FU-612 power supply unit is used.
Applications
Medium-sized to large MATV and SMATV installations. Enables distribution to up to 128 TV outlets in a single line, with a single amplifier and FU-513 power supply unit. By dividing the installation into lines of 128 outlets and distributing the 4 or 8 polarities and the terrestrial TV to all the lines, it is possible to reach more than 2,000 outlets. Amplifies and equalises all the polarities before the cascade of multiswitches.
Characteristics
Return path included from 5 to 65MHz. Shielded zamak chassis with plastic supports. F-type connectors. Two power supply jacks, 9.5mm x 2.1mm for the NET cascade and for the LNB.
Downloads
Technical specification
Technical specification
Manuals
AU-621 Manual pdf 796.9 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Distribution pdf 269.31 KB
Technical specifications
-
Alcad AU-640 Amplifier multiswitch 8 inputs
KSh60,654.00Add to cartAlcad AU-640 – Serie 913: Amplifier multiswitch 8 inputs.
SAT amplifier for 4, 8 or 16 polarities, for installations in cascade. For 16 polarities, two stacked amplifiers of 8 polarities are installed. Equipped with gain control and independent equaliser for each polarity. Requires the FU-513 power supply unit, from the NET power supply connector, to feed the amplifier and intermediate active multiswitches. To power the LNB, the FU-612 power supply unit is used.
Applications
Medium-sized to large MATV and SMATV installations. Enables distribution to up to 128 TV outlets in a single line, with a single amplifier and FU-513 power supply unit. By dividing the installation into lines of 128 outlets and distributing the 4 or 8 polarities and the terrestrial TV to all the lines, it is possible to reach more than 2,000 outlets. Amplifies and equalises all the polarities before the cascade of multiswitches.
Characteristics
Return path included from 5 to 65MHz. Shielded zamak chassis with plastic supports. F-type connectors. Two power supply jacks, 9.5mm x 2.1mm for the NET cascade and for the LNB.
Downloads
Technical specification
Technical specification
Manuals
AU-640 Manual pdf 796.9 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Distribution pdf 269.31 KB
Technical specifications
-
Alcad AU-641 Amplifier multiswitch 8 inputs 25 db
KSh52,328.00Add to cartAlcad AU-641 – Serie 913: Amplifier multiswitch 8 inputs 25 db.
SAT amplifier for 4, 8 or 16 polarities, for installations in cascade. For 16 polarities, two stacked amplifiers of 8 polarities are installed. Equipped with gain control and independent equaliser for each polarity. Requires the FU-513 power supply unit, from the NET power supply connector, to feed the amplifier and intermediate active multiswitches. To power the LNB, the FU-612 power supply unit is used.
Applications
Medium-sized to large MATV and SMATV installations. Enables distribution to up to 128 TV outlets in a single line, with a single amplifier and FU-513 power supply unit. By dividing the installation into lines of 128 outlets and distributing the 4 or 8 polarities and the terrestrial TV to all the lines, it is possible to reach more than 2,000 outlets. Amplifies and equalises all the polarities before the cascade of multiswitches.
Characteristics
Return path included from 5 to 65MHz. Shielded zamak chassis with plastic supports. F-type connectors. Two power supply jacks, 9.5mm x 2.1mm for the NET cascade and for the LNB.
Downloads
Technical specification
Technical specification
Manuals
AU-641 Manual pdf 796.9 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Distribution pdf 269.31 KB
Technical specifications
-
Add to cartAlcad AV-305 – Serie 909: Variable attenuator 18 db (5-2400 mhz).
Fixed and variable attenuators for terrestrial and satellite TV. The variable attenuators are equipped with an attenuation control. Available in different attenuation and pass bands according to the model. All models have a constant impedance of 75.
Applications
Used to attenuate signals which are too wrong. Installed at the input of equipment when the antenna level is excessive, or at the output when the output level of the equipment is excessive. Installed at the output of an outlet with excess signal, permitting a reduction in the level of signal that the television receives.
Characteristics
Shielded zamak chassis, with female input and output F connectors.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Add to cartAlcad AV-315 – Serie 909: Variable attenuator 18 db (5-2400mhz).
Fixed and variable attenuators for terrestrial and satellite TV. The variable attenuators are equipped with an attenuation control. Available in different attenuation and pass bands according to the model. All models have a constant impedance of 75. Applications Used to attenuate signals which are too wrong. Installed at the input of equipment when the antenna level is excessive, or at the output when the output level of the equipment is excessive. Installed at the output of an outlet with excess signal, permitting a reduction in the level of signal that the television receives. Characteristics Shielded zamak chassis, with female input and output F connectors.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BC-100 Terminal, attenuation 0,5 db
KSh2,190.00Add to cartAlcad BC-100 – Serie 907: Terminal, attenuation 0,5 db.
Outlets for terrestrial TV with two IEC male and female connectors. Radio and TV outputs separated by filters. Designed for use in cable TV networks. They cover frequencies between 5 and 1000 MHz.
Applications
Cable TV networks requiring the filtering of radio and TV signals at the outlet base. Installation as a terminal outlet connected to a tap-off or splitter or as outlets in series connected to each other. The outlet base facilitates the connection of the TV to the distribution and loads the distribution when the TV is not connected.
Characteristics
Voltage blockage in the output connectors with a 2 KV insulation. Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 619.4 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BC-200 Attenuation, 10 db
KSh2,384.00Add to cartAlcad BC-200 – Serie 907: Attenuation, 10 db.
Outlets for terrestrial TV with two IEC male and female connectors. Radio and TV outputs separated by filters. Designed for use in cable TV networks. They cover frequencies between 5 and 1000 MHz.
Applications
Cable TV networks requiring the filtering of radio and TV signals at the outlet base. Installation as a terminal outlet connected to a tap-off or splitter or as outlets in series connected to each other. The outlet base facilitates the connection of the TV to the distribution and loads the distribution when the TV is not connected.
Characteristics
Voltage blockage in the output connectors with a 2 KV insulation. Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 619.4 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BL-300 Current blocker (5-2400 mhz)
KSh2,892.00Add to cartAlcad BL-300 – Serie 909: Current blocker (5-2400 mhz).
DC Current blocker (5-2400MHz) for 913 series multiswitches, to avoid shortcircuits while suplying power to the switches
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BM-100 Terminal, attenuation 4 db
KSh1,754.00Add to cartAlcad BM-100 – Serie 907: Terminal, attenuation 4 db.
Outlets for terrestrial TV with two IEC male and female connectors. They cover frequencies up to 862 MHz. Applications Individual or MATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. The outlet facilitates the connection of the TV to the distribution and loads the distribution when the TV is not connected.
Characteristics
Voltage blockage in the output connectors. Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 619.4 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BM-101 Terminal, attenuation 6 db (bridge)
KSh1,452.00Add to cartAlcad BM-101 – Serie 907: Terminal, attenuation 6 db (bridge).
Outlets for terrestrial TV with two IEC male and female connectors. They cover frequencies up to 862 MHz. Applications Individual or MATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. The outlet facilitates the connection of the TV to the distribution and loads the distribution when the TV is not connected.
Characteristics
Voltage blockage in the output connectors. Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 619.4 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BM-111 Terminal, attenuation 1 db
KSh1,754.00Add to cartAlcad BM-111 – Serie 907: Terminal, attenuation 1 db.
Outlets for terrestrial TV with two IEC male and female connectors. They cover frequencies up to 862 MHz. Applications Individual or MATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. The outlet facilitates the connection of the TV to the distribution and loads the distribution when the TV is not connected.
Characteristics
Voltage blockage in the output connectors. Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 619.4 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BM-200 Attenuation 7 db
KSh2,094.00Add to cartAlcad BM-200 – Serie 907: Attenuation 7 db.
Outlets for terrestrial TV with two IEC male and female connectors. They cover frequencies up to 862 MHz. Applications Individual or MATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. The outlet facilitates the connection of the TV to the distribution and loads the distribution when the TV is not connected.
Characteristics
Voltage blockage in the output connectors. Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 619.4 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BM-500 Attenuation 12 db
KSh2,094.00Add to cartAlcad BM-500 – Serie 907: Attenuation 12 db.
Outlets for terrestrial TV with two IEC male and female connectors. They cover frequencies up to 862 MHz. Applications Individual or MATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. The outlet facilitates the connection of the TV to the distribution and loads the distribution when the TV is not connected.
Characteristics
Voltage blockage in the output connectors. Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 619.4 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BM-700 Attenuation 15 db
KSh2,094.00Add to cartAlcad BM-700 – Serie 907: Attenuation 15 db.
Outlets for terrestrial TV with two IEC male and female connectors. They cover frequencies up to 862 MHz. Applications Individual or MATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. The outlet facilitates the connection of the TV to the distribution and loads the distribution when the TV is not connected.
Characteristics
Voltage blockage in the output connectors. Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 619.4 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BO-190 Kit amp am-190 & power supply
KSh10,546.00Add to cartAlcad BO-190 – Serie 903: Kit amp am-190 & power supply.
Antennas for optimal reception of DTT channels, with the best available gain (18 dBi). Designed to cover the UHF band up to 790 MHz while rejecting the LTE mobile telephone band. Easy to mount and adjust, providing maximum robustness and ensuring complete safety of installation. With a stylish design which perfectly reflects the excellent electrical and mechanical qualities of the antenna.
Applications
Digital and analogue terrestrial TV installations, collective or individual, where rejection of the LTE band is necessary and high gain and directivity are required. The reflectors prevent interference produced by the signals received from the rear of the antenna.
Characteristics
Rejection of LTE and GSM signals. Manufactured in aluminium, zamak weather-resistant plastic and galvanised steel. Innovative spring-loaded clamp system for attaching to the mast, making installation even easier. The simplified pointing system with the antenna already fastened to the mast enables adjustments using a single hand. System for changing polarisation without removing the antenna from the mast. Watertight matching transformer casing (IP55). Matching transformer, with F-type connector, protected inside the casing. System of front-fixing reflectors for greater ease of assembly. No tools required for installation. Supplied in an individual pack.
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
-
Alcad BO-195 Kit amp am-195 & power supply
KSh10,690.00Add to cartAlcad BO-195 – Serie 903: Kit amp am-195 & power supply.
Kits consisting of a mast amplifier and a power supply unit. Both products are included in a single pack.
Characteristics
The characteristics are identical to those of the products which are supplied independently.
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
-
Alcad BO-292 Kit amp am-292 & power supply
KSh11,706.00Add to cartAlcad BO-292 – Serie 903: Kit amp am-292 & power supply.
Kits consisting of a mast amplifier and a power supply unit. Both products are included in a single pack.
Characteristics
The characteristics are identical to those of the products which are supplied independently.
Accessories
9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
-
Alcad BO-296 Kit amp am-296 & power supply
KSh12,196.00Add to cartAlcad BO-296 – Serie 903: Kit amp am-296 & power supply.
Kits consisting of a mast amplifier and a power supply unit. Both products are included in a single pack.
Characteristics
The characteristics are identical to those of the products which are supplied independently.
Accessories
9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
-
Alcad BO-396 Kit amp am-396 & power supply
KSh15,982.00Add to cartAlcad BO-396 – Serie 903: Kit amp am-396 & power supply.
Kits consisting of an AM-396 mast amplifier and an AL-100 power supply unit. Both products are included in a single pack.
Characteristics
The characteristics are identical to those of the products which are supplied independently.
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 251.86 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
Technical specifications
-
Alcad BO-397 Kit amp am-397 & power supply 24 vdc
KSh11,630.00Add to cartAlcad BO-397 – Serie 903: Kit amp am-397 & power supply 24 vdc.
Kits consisting of a mast amplifier and a power supply unit. Both products are included in a single pack.
Characteristics
The characteristics are identical to those of the products which are supplied independently.
Accessories
9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 232.44 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
DEC_AM_LTE700 pdf 65.95 KB
-
Alcad BO-497 Kit amp am-497 & power supply 24 vdc
KSh14,170.00Add to cartAlcad BO-497 – Serie 903: Kit amp am-497 & power supply 24 vdc.
Kits consisting of a mast amplifier and a power supply unit. Both products are included in a single pack.
Characteristics
The characteristics are identical to those of the products which are supplied independently.
Accessories
9120039 CM-004 Male F connector for **6.6 mm coaxial. 9080023 MC-302 Male F connector for RG-6 coaxial, **7.0 mm
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 368.98 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems_AL-BO pdf 34.29 KB
-
Alcad BO-696 Kit amp am-696 & power supply al-245
KSh17,524.00Add to cartAlcad BO-696 – Serie 903: Kit amp am-696 & power supply al-245.
Kits consisting of a mast amplifier and a power supply unit. Both products are included in a single pack.
Characteristics
The characteristics are identical to those of the products which are supplied independently.
Downloads
Technical specification
Technical specification
Manuals
BO-696 HN pdf 824.47 KB
BO-696 Manual pdf 991.42 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE Declaration – BO-696 pdf 71 KB
Technical specifications
-
Alcad BO-915 Kit amp am-915 & power supply
KSh12,722.00Add to cartAlcad BO-915 – Serie 903: Kit amp am-915 & power supply.
Kits consisting of an AM-915 mast amplifier and an AL-100 power supply unit. Both products are included in a single pack.
Characteristics
The characteristics are identical to those of the products which are supplied independently.
Downloads
Technical specification
Technical specification
Manuals
Manual pdf 299.28 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Systems pdf 65.95 KB
Technical specifications
-
Alcad BS-100 If outlet (f connector)
KSh2,396.00Add to cartAlcad BS-100 – Serie 907: If outlet (f connector).
Outlets for terrestrial and satellite TV with two IEC male and female connectors (except for the BS-100 outlet). They cover frequencies up to 2,400 MHz. They have a DC path from one of their outputs to the input and from the through output in the intermediate outlets to the input.
Applications
Individual or SMATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. They permit the feeding of a preamplifier or of an LNB through the output. A control voltage can be used in installations with multiswitches.
Characteristics
Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 611.12 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Certificates
CE_Declaration-TV_Distribution pdf 269.31 KB
Technical specifications
-
Read moreAlcad BS-102 – Serie 907: If terminal outlet, 2 db, 3 connectors.
Outlets for terrestrial and satellite TV with three male IEC connectors, an IEC female connector and an F-type female connector. They cover frequencies up to 2,300MHz. They allow a feed path via the female F-type connector to the input.
Applications
Outlets for terrestrial and satellite TV with three male IEC connectors, an IEC female connector and an F-type female connector. They cover frequencies up to 2,300MHz. They allow a feed path via the female F-type connector to the input.
Characteristics
Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Includes TV/R/SAT frontplate, surface box and screws for fixing to a wall.
Downloads
Technical specification
Technical specification
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BS-110 Terminal, attenuation 5 db
KSh2,202.00Add to cartAlcad BS-110 – Serie 907: Terminal; attenuation 5 db.
Outlets for terrestrial and satellite TV with two IEC male and female connectors (except for the BS-100 outlet). They cover frequencies up to 2,400 MHz. They have a DC path from one of their outputs to the input and from the through output in the intermediate outlets to the input.
Applications
Individual or SMATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. They permit the feeding of a preamplifier or of an LNB through the output. A control voltage can be used in installations with multiswitches.
Characteristics
Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 611.12 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BS-112 Terminal, attenuation 1 db
KSh1,972.00Add to cartAlcad BS-112 – Serie 907: Terminal, attenuation 1 db.
Outlets for terrestrial and satellite TV with two IEC male and female connectors (except for the BS-100 outlet). They cover frequencies up to 2,400 MHz. They have a DC path from one of their outputs to the input and from the through output in the intermediate outlets to the input.
Applications
Individual or SMATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. They permit the feeding of a preamplifier or of an LNB through the output. A control voltage can be used in installations with multiswitches.
Characteristics
Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 611.12 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BS-113 Outlet terminal, attenuation 1 db
KSh1,802.00Add to cartAlcad BS-113 – Serie 907: Outlet terminal, attenuation 1 db.
Outlet for terrestrial and satellite TV without brackets, for mounting in flush-mounted box with screws. The electrical characteristics are the same as those of the BS-112 model (see page 340).
Downloads
Technical specification
Technical specification
Manuals
– pdf 611.12 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Alcad BS-210 Attenuation 10 db
KSh2,504.00Add to cartAlcad BS-210 – Serie 907: Attenuation 10 db.
Outlets for terrestrial and satellite TV with two IEC male and female connectors (except for the BS-100 outlet). They cover frequencies up to 2,400 MHz. They have a DC path from one of their outputs to the input and from the through output in the intermediate outlets to the input.
Applications
Individual or SMATV installations. Installation as a terminal outlet connected to a tap-off or splitter, or as outlets in series connected to each other. They permit the feeding of a preamplifier or of an LNB through the output. A control voltage can be used in installations with multiswitches.
Characteristics
Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 611.12 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
-
Add to cartAlcad BS-220 – Serie 907: If outlet 12 db cascade (5-2400 mhz).
Outlets for terrestrial and satellite TV with two IEC male and female connectors. They cover frequencies up to 2,400 MHz.
Applications
SMATV installations. Installation as outlets in series connected to each other. The outlet facilitates the connection of the TV to the distribution and loads the distribution when the TV is not connected.
Characteristics
Voltage blockage in the output connectors. Shielded zamak and metal plate chassis. Connection of the coaxial cable by means of screw terminal. Fits in a **60 mm box.
Downloads
Technical specification
Technical specification
Manuals
– pdf 180.78 KB
Catalogues
CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 5.42 MB
Technical specifications
Popular Products
-
Starlink In Person Verification Services In Kenya
KSh3,000.00
-
Starlink Gen 3 Case Compatible with Starlink Gen 3, Waterproof Starlink Standard Case, Shockproof Starlink Carrying Bag for Satellite Dish Accessories, Travel Bag for Camping and RV
-
STARLINK Gen3 Portable Accessory Storage Bag, Outdoor Camping, Portable Handbag, Made Of Polyester Material.
-
Carrying Bag For Starlink V4 Satellite Portable RV Outdoor Travel Bag Rectangular Storage Handbag For Starlink Gen3 Accessory
-
IsatPhone Link 50 Units - 30 Days
Validity
Products
-
Starlink In Person Verification Services In Kenya
KSh3,000.00
-
Starlink Gen 3 Case Compatible with Starlink Gen 3, Waterproof Starlink Standard Case, Shockproof Starlink Carrying Bag for Satellite Dish Accessories, Travel Bag for Camping and RV
-
STARLINK Gen3 Portable Accessory Storage Bag, Outdoor Camping, Portable Handbag, Made Of Polyester Material.
-
Carrying Bag For Starlink V4 Satellite Portable RV Outdoor Travel Bag Rectangular Storage Handbag For Starlink Gen3 Accessory
-
IsatPhone Link 50 Units - 30 Days
Validity
